John Deere 9430 9530 9630 Tractors Diagnosis Service Manual

John Deere 9230 9330 9430 9530 9630 4WD Articulated Tractors Repair Service ManualTM2254 - JOHN DEERE 9230, 9330, 9430, 9530, 9630, diagnosis test manual

John Deere 9430 9530 9630 Tractors Diagnosis Service Manual

TM2254

TM2267 John Deere 9230 9330 9430 9530 9630 4WD Articulated

Illustrated Factory Diagnosis and Tests Service Manual for John Deere 4WD Articulated Tractors 9230, 9330, 9430, 9530 and 9630

This manual contains high quality images, circuit diagrams, diagnostic procedures to help you to diagnostic, troubleshoot and repair your truck. This document is printable, without restrictions, contains searchable text, bookmarks, crosslinks for easy navigation.

This guide carries excessive first-rate images, circuit diagrams, commands that will help you to operate, maintenance, diagnostic, and restore your truck. This record is printable, with out restrictions, carries searchable text, bookmarks, crosslinks for clean navigation.

Covered models:
9230
9330
9430
9530
9630

Complete Diagnosis & Tests Technical Manual with electrical wiring diagrams for John Deere 9230, 9330, 9430, 9530, 9630 Articulated Tractors, with workshop information to maintain, diagnose, and rebuild like professional mechanics.

John Deere 4WD Articulated Tractors 9230, 9330, 9430, 9530 and 9630 workshop Diagnosis & Tests technical manual includes:

  • Numbered table of contents easy to use so that you can find the information you need fast.
  • Detailed sub-steps expand on repair procedure information
  • Numbered instructions guide you through every repair procedure step by step.
  • Troubleshooting and electrical service procedures are combined with detailed wiring diagrams for ease of use.
  • Notes, cautions and warnings throughout each chapter pinpoint critical information.
  • Bold figure number help you quickly match illustrations with instructions.
  • Detailed illustrations, drawings and photos guide you through every procedure.
  • Enlarged inset helps you identify and examine parts in detail.

MAIN SECTIONS
Foreword
GENERAL
Safety
General References
DIAGNOSTIC TROUBLE CODES
OBSERVABLE SYMPTOMS
Engines
Fuel and Air
Electrical
Control Units
Power Shift Transmission
Manual Shift Transmission
Drive Systems
Steering and Brakes
Hydraulics
Operator Station
SYSTEM DIAGNOSIS
Electrical
CAN
Powershift Transmission
Manual Shift Transmission
Drive Systems
Steering and Brakes
Hydraulics
Operator Station
ENGINES
Engine Performance
Engine Cooling System
Engine Lubrication System
FUEL AND AIR INTAKE SYSTEMS
Engine Fuel System
Engine Air Intake and Exhaust System
ELECTRICAL
Load Center Fuses, Relays and Ground Points
Operational Checks
Tests and Adjustments
Functional Schematics and Components Reference Lists
Connector Information
Harness Information
SE01 – Power Supply, Starting and Charging
SE02 – Manual Seat
SE03 – Manual A/C and Automatic Temperature Control (ATC)
SE04 – Remote Mirror Option
SE05 – Radio, Dome Lamp and Steering Column Module
SE06 – CLC/TEC – Implement Gateway Control Unit Functions
SE06A – CLC/TEC – Cab Load Center Control Unit and Tractor Equipment Control Unit Functions
SE06B – CLC – North American Lighting Functions
SE06C – CLC – European Lighting Functions
SE07 – Accessory Connectors
SE08 – Controller Area Network (CAN) Termination
SE09 – CPD – Corner Post Display, ICU – Information Display, and SUP – SCV Setup Panel Display
SE10 – CAB/ASU – Cab Control Unit Functions
SE10A – CAB – CAB Control Unit Functions
SE10B – ASU – Active Seat Control Unit Functions
SE11 – VLC/CCU – Vehicle Control Unit Functions
SE11A – CCU – Chassis Control Unit Functions
SE11B – VLC – Vehicle Load Center Control Unit Functions
SE12 – PTP – Powershift Transmission Control Unit Functions
SE13 – ACU – Armrest Control Unit Functions
SE14 – SCU/HCU/BRC – Deluxe Hydraulic Controller Function
SE14A – HCU – Hitch Control Unit Functions
SE14B – SCU – SCV Selective Control Unit Functions
SE14D – BRC – Brake System Control Unit Functions
SE14 CAN – SCC/HCC – Deluxe Hydraulic CAN Control Unit Functions
SE14A CAN – SCC – Selective CAN Control Unit Functions
SE14B CAN – HCC – Hitch CAN Control Unit Functions
SE15 – SCO – Secondary Hydraulic Control Unit Functions
SE16A – Engine Control Unit (ECU) Level 14 (9.0L) Functions
SE16B – Engine Control Unit (ECU) Level 15 (13.5L) Functions
SE17 – JDL – JDLink™Control Unit Functions
SE18 – GreenStar™ Display, Receiver, & Processor
SE20 – SSU – Steering System Control Unit Functions

POWERSHIFT TRANSMISSION
Powershift Transmission
MANUAL SHIFT TRANSMISSION
Manual Shift Transmission
DRIVE SYSTEMS
Axles and Differential Lock
PTO
STEERING AND BRAKES
Brakes
Steering
HYDRAULICS
Main Hydraulics
OPERATOR STATION
Air Conditioning
Seat
SERVICE TOOLS AND INSTALLING TEST EQUIPMENT
Dealer Fabricated Tools
Service Tools and Kits
Electrical Install Test Equipment
Powershift Transmission Install Test Equipment
Manual Shift Transmission Install Test Equipment
Drive Systems Install Test Equipment
Steering and Brakes Install Test Equipment
Hydraulics Install Test Equipment
Operator Station Install Test Equipment

John Deere Tractors 9430 9530 9630 Service Manual

John Deere Tractors 9230 9330 9430 9530 9630 Diagnosis and Tests Service Manual TM2254
John Deere Tractors 9230 9330 9430 9530 9630 Diagnosis and Tests Service Manual TM2254
FREE MANUAL DOWNLOAD
Price: $169.99

Table of Contents
Foreword
Section 210: GENERAL
Group 05: Safety
Recognize Safety Information
Understand Signal Words
Handle Fluids SafelAvoid Fires
Follow Safety Instructions
Wear Protective Clothing
Service Machines Safely
Handle Fluids Safely—Avoid Fires
Prevent Battery Explosions
Prepare for Emergencies
Remove Paint Before Welding or Heating
Avoid Heating Near Pressurized Fluid Lines
Handle Starting Fluid Safely
In Case of Fire
Avoid Static Electricity Risk When Refueling
Avoid Hot Exhaust
Prevent Acid Burns
Handle Agricultural Chemicals Safely
Clean Vehicle of Hazardous Pesticides
Handling Batteries Safely
Avoid Harmful Asbestos Dust
Avoid High-Pressure Fluids
Park Machine Safely
Support Machine Properly
Work in Clean Area
Work In Ventilated Area
Illuminate Work Area Safely
Use Proper Lifting Equipment
Use Steps and Handholds Correctly
Install All Guards
Transport Tractor Safely
Wait Before Opening High-Pressure Fuel System
Service Accumulator Systems Safely
Use Seat Belt Properly
Keep ROPS Installed Properly
Passenger Seat
Instructional Seat
Service Tires Safely
Practice Safe Maintenance
Use Proper Tools
Decommissioning — Proper Recycling and Disposal of Fluids and Components
Prevent Machine Runaway
Service Cooling System Safely
Stay Clear of Rotating Drivelines
Protect Against High Pressure Spray
Construct Dealer-Made Tools Safely
Live With Safety
Group 15: General References
General Reference List
Bolt and Cap Screw Torque Values
Glossary of Terms
JIC Hydraulic Symbols
Trademarks
Wiring Diagram and Schematic Information
Electrical Schematic Symbols
Reading Wiring Schematics and Diagrams
Visually Inspect Electrical System
Seven Step Electrical Test Procedure With probe light or multimeter
Using a Probe Light
Circuit Types
Circuit Malfunctions
Troubleshooting Circuit Malfunctions
Understanding Electrical vs. Electronic Circuits
Intermittent Electronic Problems
Relay Circuit Types
Using a Digital Multimeter
Troubleshooting Unresolved Electrical/Electronic Problems
Section 211: DIAGNOSTIC TROUBLE CODES
Group ACU: ACU Code Diagnostics
ACU 000110.14 – Engine Coolant Temperature Moderately High
ACU 000158.04 – ACU Switched Supply Voltage Low
ACU 000237.02 – VIN Security Data Conflict
ACU 000237.14 – VIN Security Not Enabled
ACU 000237.31 – VIN Security Messages Missing
ACU 000628.02 – ACU EOL Data Fault
ACU 000628.12 – ACU Programming
ACU 000629.11 – ACU Control Unit Fault
ACU 000629.12 – ACU Control Unit Fault
ACU 000630.13 – ACU Calibration Fault/Not Calibrated
ACU 000639.12 – ACU CAN Message Overflow
ACU 000639.14 – ACU CAN Error Limit Exceeded
ACU 000974.02 – Hand Throttle Sensor Circuit Voltage Conflict
ACU 000974.03 – Hand Throttle Sensor Circuit Voltage High
ACU 000974.04 – Hand Throttle Sensor Circuit Voltage Low
ACU 001079.03 – ACU Sensor Supply 1 Voltage High
ACU 001079.04 – ACU Sensor Supply 1 Voltage Low
ACU 001080.03 – ACU Sensor Supply 2 Voltage High
ACU 001080.04 – ACU Sensor Supply 2 Voltage Low
ACU 002000.09 – ECU Message Missing
ACU 002003.09 – PTP Message Missing
ACU 002049.09 – CAB Control Unit Message Missing
ACU 523775.02 – Single Lever Control Hand Presence Switch Fault
ACU 523776.02 – Single Lever Control Transport Lock Switch Circuit Fault
ACU 523801.02 – Single Lever Control Auxiliary Switch Fault
ACU 523804.02 – Single Control Lever Lateral Detent Switch Circuit Fault
ACU 523804.03 – Single Lever Control Lateral Sensor Circuit Voltage High
ACU 523804.04 – Single Lever Control Lateral Sensor Circuit Voltage Low
ACU 523805.02 – Single Lever Control Fore-Aft Detent Switch Circuit Fault
ACU 523805.03 – Single Lever Control Fore-Aft Sensor Circuit Voltage High
ACU 523805.04 – Single Lever Control Fore-Aft Sensor Circuit Voltage Low
ACU 523923.02 – SCV I Control Lever Switch/Sensor Conflict
ACU 523923.03 – SCV I Control Lever Sensor Circuit Voltage High
ACU 523923.04 – SCV I Control Lever Sensor Circuit Voltage Low
ACU 523960.31 – Operator Not Seated During Reverser Command
ACU 523968.02 – IMS Switch Circuits Conflict
ACU 523968.03 – IMS Switch Circuits Voltage High
ACU 523968.04 – IMS Switch Circuits Voltage Low
ACU 524018.31 – RHR Neutral/Park Transition Fault
ACU 524019.31 – Shift Lever Transition Fault
ACU 524020.31 – Transmission in Gear at Power Up
ACU 524021.31 – Multiple Reverser Switches Conflict
ACU 524101.02 – SCV VI Control Lever Switch/Sensor Circuit Conflict
ACU 524101.03 – SCV VI Control Lever Sensor Circuit Voltage High
ACU 524101.04 – SCV VI Control Lever Sensor Circuit Voltage Low
ACU 524102.02 – SCV V Control Lever Switch/Sensor Circuit Conflict
ACU 524102.03 – SCV V Control Lever Sensor Circuit Voltage High
ACU 524102.04 – SCV V Control Lever Sensor Circuit Voltage Low
ACU 524103.02 – SCV IV Control Lever Switch/Sensor Circuit Conflict
ACU 524103.03 – SCV IV Control Lever Sensor Circuit Voltage High
ACU 524103.04 – SCV IV Control Lever Sensor Circuit Voltage Low
ACU 524104.02 – SCV III Control Lever Switch/Sensor Circuit Conflict
ACU 524104.03 – SCV III Control Lever Sensor Circuit Voltage High
ACU 524104.04 – SCV III Control Lever Sensor Circuit Voltage Low
ACU 524105.02 – SCV II Control Lever Switch/Sensor Circuit Conflict
ACU 524105.03 – SCV II Control Lever Sensor Circuit Voltage High
ACU 524105.04 – SCV II Control Lever Sensor Circuit Voltage Low
ACU 524212.02 – Rear Hitch Control Lever Switch/Sensor Circuit Conflict
ACU 524212.03 – Rear Hitch Control Lever Sensor Circuit Voltage High
ACU 524212.04 – Rear Hitch Control Lever Sensor Circuit Voltage Low
ACU 524222.02 – Resume Switch Circuit Conflict
ACU 524224.02 – Rear PTO Switch Circuit Conflict
ACU 524254.31 – Transmission Enable Relay Circuit Fault
Group ASU: ASU Code Diagnostics
ASU 000629.12 – ASU Control Unit Fault
ASU 524002.31 – Active Seat Pressure Control Solenoid Fault
ASU 524003.02 – Active Seat Firmness Control Switch Circuit Fault
ASU 524004.02 – Active Seat Height Control Switch Circuit Fault
ASU 524006.30 – Active Seat Vent ON Too Long
ASU 524007.30 – Active Seat Compressor Assembly ON Too Long
ASU 524008.13 – ASU Not Calibrated
ASU 524010.31 – Active Seat Raise/Lower Solenoid Circuit Fault
ASU 524011.03 – Active Seat Accelerometer Circuit Voltage High
ASU 524011.04 – Active Seat Accelerometer Circuit Voltage Low
ASU 524011.08 – Active Seat Accelerometer Circuit Fault
ASU 524012.03 – Active Seat Position Sensor Circuit Voltage High
ASU 524012.04 – Active Seat Position Sensor Circuit Voltage Low
Group ATC: ATC Code Diagnostics
ATC 000170.03 – Cab Temperature Sensor Circuit Voltage High
ATC 000170.04 – Cab Temperature Sensor Circuit Voltage Low
ATC 000628.12 – ATC Programming
ATC 000630.02 – ATC Calibration Fault/Data Invalid
ATC 000639.14 – ATC CAN Error Exceeded
ATC 000871.03 – Refrigerant Pressure Sensor Circuit Voltage High
ATC 000871.04 – Refrigerant Pressure Sensor Circuit Voltage Low
ATC 000871.13 – B130 – Sensor for Refrigerant Pressure, Refrigerant Pressure Out of Valid Range Low
ATC 000876.03 – Compressor Clutch Circuit Voltage High
ATC 000876.04 – Compressor Clutch Circuit Voltage Low
ATC 000876.10 – Excessive A/C Clutch Cycling
ATC 000876.14 – Compressor Shutoff Due to Engine Overheat
ATC 000923.03 – Circulation Blower Motor Circuit Voltage High
ATC 000923.04 – Circulation Blower Motor Circuit Voltage Low
ATC 000923.12 – Circulation Blower Motor Driver Circuit Fault
ATC 001079.03 – ATC Sensor Supply Voltage High
ATC 001079.04 – ATC Sensor Supply Voltage Low
ATC 001546.03 – Water Valve Position Sensor Circuit Voltage High
ATC 001546.04 – Water Valve Position Sensor Circuit Voltage Low
ATC 001547.03 – Evaporator Temperature Sensor Circuit Voltage High
ATC 001547.04 – Evaporator Temperature Sensor Circuit Voltage Low
ATC 001548.03 – Outlet Air Temperature Sensor Circuit Voltage High
ATC 001548.04 – Outlet Air Temperature Sensor Circuit Voltage Low
ATC 001549.03 – Water Valve Motor Circuit Voltage High
ATC 001549.04 – Water Valve Motor Circuit Voltage Low
ATC 001549.07 – Water Valve Motor Mechanical Fault
ATC 001549.13 – Water Valve Motor Not Calibrated
ATC 001551.03 – Pressurizer Blower Motor Circuit Voltage High
ATC 001551.04 – Pressurizer Blower Motor Circuit Voltage Low
ATC 001552.03 – Cab Temperature Control Circuit Voltage High
ATC 001552.04 – Cab Temperature Control Circuit Voltage Low
ATC 001553.03 – Blower Control Circuit Voltage High
ATC 001553.04 – Blower Control Circuit Voltage Low
ATC 002000.09 – ECU Message Missing
ATC 523848.03 – Air Flow Mode Motor Circuit Voltage High
ATC 523848.04 – Air Flow Mode Motor Circuit Voltage Low
ATC 523848.05 – Air Flow Mode Motor Circuit Current Low
ATC 523848.06 – Air Flow Mode Motor Circuit Current High
ATC 523848.07 – Air Flow Mode Motor Mechanical Fault
ATC 523848.13 – Air Flow Mode Motor Not Calibrated
ATC 524203.03 – Ambient Temperature Sensor Circuit Voltage High
ATC 524203.04 – Ambient Temperature Sensor Circuit Voltage Low
Group BRC: BRC Code Diagnostics
BRC 000158.04 – BRC Switched Supply Voltage Low
BRC 000168.04 – BRC Unswitched Supply Voltage Low
BRC 000628.02 – BRC EOL Data Fault
BRC 000629.12 – BRC Control Unit Fault
BRC 000630.13 – BRC Calibration/Not Calibrated
BRC 001079.03 – BRC Sensor Supply Voltage High
BRC 001079.04 – BRC Sensor Supply Voltage Low
BRC 002000.09 – ECU Message Missing
BRC 002049.09 – CAB Message Missing
BRC 002071.09 – CCU Message Missing
BRC 522279.05 – Secondary Brake Control Valve Current Low
BRC 522279.06 – Secondary Brake Control Valve Current High
BRC 522279.13 – Secondary Brake Control Valve Not Calibrated
BRC 522280.00 – Secondary Brake Pressure High
BRC 522280.01 – Secondary Brake Pressure Low
BRC 522280.03 – Secondary Brake Pressure Sensor Voltage High
BRC 522280.04 – Secondary Brake Pressure Sensor Voltage Low
BRC 522280.13 – Secondary Brake Pressure Not Calibrated
BRC 522281.05 – Rear Brake Cooling Valve Current Low
BRC 522281.06 – Rear Brake Cooling Valve Current High
BRC 523652.02 – Wire Connector Fault
BRC 523778.05 – Front Brake Cooling Valve Current Low
BRC 523778.06 – Front Brake Cooling Valve Current High
BRC 523787.04 – Brake Cooling Control Valve Supply Voltage Low
BRC 523839.19 – Secondary Brake Switch Fault
BRC 523841.19 – Secondary Brake Position Fault Message Received
BRC 523841.31 – Secondary Brake Position Message Missing
BRC 523910.02 – BRC Control Unit Fault
BRC 524016.04 – Secondary Brake Solenoid Supply Voltage Low
BRC 524088.31 – Brake Cooling System Fault
BRC 524157.19 – Brake Pedal Switch Fault Message Received
Group CAB: CAB Code Diagnostics
CAB 000158.03 – CAB Control Unit Switched Supply Voltage High
CAB 000158.04 – CAB Control Unit Switched Supply Voltage Low
CAB 000628.02 – CAB Control Unit EOL Data Fault
Cab 000628.12 – CAB Control Unit Programming
CAB 000629.12 – CAB Control Unit Fault
CAB 001079.02 – CAB Control Unit Sensor Supply Voltage Fault
CAB 001079.03 – CAB Control Unit Sensor Supply Voltage High
CAB 001079.04 – CAB Control Unit Sensor Supply Voltage Low
CAB 001504.30 – Seat Switch Circuit Fault
CAB 002876.02 – Turn Signal Switch Conflict
CAB 523839.02 – Secondary Brake Switch Conflict
CAB 523839.13 – Secondary Brake Not Calibrated
CAB 523841.03 – Secondary Brake Sensor Voltage High
CAB 523841.04 – Secondary Brake Sensor Voltage Low
CAB 523922.31 – Secondary Brake ON While Moving
CAB 524016.04 – CAB Control Unit Switched Supply Voltage Low
CAB 524017.13 – Reverser Lever Type Not Selected
CAB 524166.02 – Right Brake Pedal Switch Circuit Conflict
CAB 524166.03 – Right Brake Pedal Sensor Circuit Voltage High
CAB 524166.04 – Right Brake Pedal Sensor Circuit Voltage Low
CAB 524166.13 – Right Brake Pedal Sensor Not Calibrated
CAB 524166.30 – Right Brake Pedal Sensor Adjustment Fault
CAB 524173.02 – Clutch Pedal Sensor Voltage Conflict
CAB 524173.03 – Clutch Pedal Sensor Circuit Voltage High
CAB 524172.04 – Clutch Pedal Sensor Circuit Voltage Low
Group CCU: CCU Code Diagnostics
CCU 000090.03 – Rear PTO Oil Temperature Sensor Circuit Voltage High
CCU 000090.04 – Rear PTO Oil Temperature Sensor Circuit Voltage Low
CCU 000096.03 – Fuel Level Sensor Circuit Voltage High
CCU 000096.17 – Fuel Level Low
CCU 000107.00 – Engine Air Filter Restriction/Engine Limited to Low Idle
CCU 000107.03 – Engine Air Filter Restriction Sensor Voltage High
CCU 000107.04 – Engine Air Filter Restriction Sensor Voltage Low
CCU 000107.15 – Engine Air Filter Becoming Restricted
CCU 000107.16 – Engine Air Filter Restricted/Engine De-rated
CCU 000126.16 – Transmission Oil Filter Restricted
CCU 000127.01 – Transmission Oil Pressure Very Low
CCU 000127.03 – Transmission Oil Pressure Sensor Voltage High
CCU 000127.04 – Transmission Oil Pressure Sensor Voltage Low
CCU 000158.01 – CCU Switched Supply Voltage Low
CCU 000168.03 – CCU Unswitched Supply Voltage High
CCU 000168.04 – CCU Unswitched Supply Voltage Low
CCU 000237.02 – VIN Security Data Conflict
CCU 000237.14 – VIN Security Not Enabled
CCU 000237.31 – VIN Security Messages Missing
CCU 000567.05 – Front Differential Lock Solenoid Circuit Fault
CCU 000569.05 – Rear Differential Lock Solenoid Circuit Fault
CCU 000628.02 – Chassis Control Unit (CCU) End Of Line (EOL) Memory Fault
CCU 000628.12 – Chassis Control Unit (CCU) Programming Fault
CCU 000630.14 – Rear PTO Configuration Invalid
CCU 000976.14 – PTO Information Conflict
CCU 001079.03 – Chassis Control Unit (CCU) Sensor Supply Voltage High
CCU 001079.04 – Chassis Control Unit (CCU) Sensor Supply Voltage Low
CCU 001638.00 – Hydraulic Oil Temperature Very Hot
CCU 001638.03 – Hydraulic Oil Temperature Sensor Circuit Voltage Low
CCU 001638.04 – Hydraulic Oil Temperature Sensor Circuit Voltage High
CCU 001638.16 – Hydraulic Oil Temperature High
CCU 001713.00 – Hydraulic Oil Filter Restricted
CCU 001883.00 – Rear PTO Over-Speed
CCU 001883.01 – Rear PTO Under-Speed
CCU 001883.13 – Rear PTO Not Calibrated
CCU 002392.05 – Back Up Alarm Circuit Fault
CCU 002602.01 – Hydraulic Oil Level Very Low
CCU 002602.02 – Hydraulic Oil Level Sensor Fault
CCU 002613.01 – Rear Axle Lube Oil Pressure Very Low
CCU 002613.03 – Rear Axle Lube Oil Pressure Switch Voltage High
CCU 002613.04 – Rear Axle Lube Oil Pressure Switch Voltage Low
CCU 002613.16 – Rear Axle Lube Oil Pressure Low
CCU 002614.00 – Secondary Steering Pressure Very Low
CCU 002614.03 – Secondary Steering Pressure Switch Stuck
CCU 523698.09 – AMS Display Message Missing
CCU 523749.16 – PTO Clutch Slipping Too Long
CCU 523770.05 – MST Hi/Lo Solenoid Circuit Fault
CCU 523777.05 – Secondary Steering Pressure Switch Open Circuit
CCU 523830.04 – IMS Reverse Detect Switch Open
CCU 523844.12 – Front Differential Lock Solenoid Fault
CCU 523851.02 – IMS Disabled Due to HCU/SCU/SCO/TEC
CCU 524016.04 – Chassis Control Unit (CCU) Switched Supply Voltage Low
CCU 524067.01 – Rear Double Reduction Axle Lube Pressure Very Low
CCU 524067.03 – Rear Double Reduction Axle Lube Pressure Sensor Voltage High
CCU 524067.04 – Rear Double Reduction Axle Lube Pressure Sensor Voltage Low
CCU 524067.05 – Axle Lube Pressure Solenoid Circuit Fault
CCU 524068.01 – Front Axle Lube Pressure Extremely Low
CCU 524068.03 – Front Axle Lube Pressure Sensor Circuit Shorted
CCU 524068.04 – Front Axle Lube Pressure Sensor Circuit Open
CCU 524068.05 – Front Axle Lube Pressure Solenoid Circuit Fault
CCU 524223.03 – Differential Lock Switch Circuit Voltage High
CCU 524224.02 – Rear PTO Switch Voltage Mismatch
CCU 524224.14 – Rear PTO Disabled
CCU 524251.31 – Operator Not Present With Rear PTO On
CCU 524252.05 – Rear PTO Solenoid Circuit Fault
CCU 524267.16 – MST Clutch Slipping Too Long
Group CLC: CLC Code Diagnostics
CLC 000158.00 – Cab Load Center (CLC) Switched Supply Voltage High
CLC 000158.01 – Cab Load Center (CLC) Switched Supply Voltage Low
CLC 000158.17 – Cab Load Center (CLC) Switched Supply Voltage Low With Engine OFF
CLC 000158.18 – Cab Load Center (CLC) Switched Supply Voltage Low With Engine Below 1500 RPM
CLC 000628.02 – Cab Load Center (CLC) End Of Line (EOL) Data Fault
CLC 000628.12 – Cab Load Center (CLC) Control Unit Programming
CLC 000629.12 – Cab Load Center (CLC) Control Unit Fault
CLC 001079.03 – Cab Load Center (CLC) Control Unit Sensor Supply Voltage High
CLC 001079.04 – Cab Load Center (CLC) Control Unit Sensor Supply Voltage Low
CLC 002050.06 – Cab Load Center (CLC) Control Unit Current High
CLC 002360.05 – Rear Fender Inner Flood Lights Circuit Current Low
CLC 002360.06 – Rear Fender Inner Flood Lights Circuit Current High
CLC 002362.05 – Rear-Facing Side Roof Flood Lights Circuit Current Low
CLC 002362.06 – Rear-Facing Side Roof Flood Lights Circuit Current High
CLC 002364.05 – Rear Fender Outer Flood Lights Circuit Current Low
CLC 002364.06 – Rear Fender Outer Flood Lights Circuit Current High
CLC 002366.05 – Front-Facing Side Roof Flood Lights Circuit Current Low
CLC 002366.06 – Front-Facing Side Roof Flood Lights Circuit Current High
CLC 002368.05 – Left Turn Signal Lights Circuit Current Low
CLC 002368.06 – Left Turn Signal Lights Circuit Current High
CLC 002370.05 – Right Turn Signal Lights Circuit Current Low
CLC 002370.06 – Right Turn Signal Lights Circuit Current High
CLC 002372.05 – Brake Lights Circuit Current Low
CLC 002372.06 – Brake Lights Circuit Current High
CLC 002378.05 – Tail Lights Circuit Current Low
CLC 002378.06 – Tail Lights Circuit Current High
CLC 002394.05 – Trailer Flood Light Circuit Current Low
CLC 002394.06 – Trailer Flood Light Circuit Current High
CLC 002863.02 – Front Wiper Switch Circuit Fault
CLC 002865.02 – Rear Wiper Switch Circuit Fault
CLC 002872.02 – Road Light Switch Circuit Fault
CLC 522310.05 – Cab Load Center (CLC) Control Unit ELX Output 1 Circuit Current Low
CLC 522310.06 – Cab Load Center (CLC) Control Unit ELX Output 1 Circuit Current High
CLC 522433.05 – Rear Wiper Motor Circuit Current Low
CLC 522433.06 – Rear Wiper Motor Circuit Current High
CLC 522434.05 – Front Wiper Motor Low Speed Circuit Current Low
CLC 522434.06 – Front Wiper Motor Low Speed Circuit Current High
CLC 522435.05 – Front Wiper Motor High Speed Circuit Current Low
CLC 522435.06 – Front Wiper Motor High Speed Circuit Current High
CLC 524016.05 – Cab Load Center (CLC) Control Unit Wake-Up Circuit Current Low
CLC 524016.06 – Cab Load Center (CLC) Control Unit Wake-Up Circuit Current High
CLC 524259.00 – CLC Temperature Above 115 Degrees Celsius
CLC 524259.15 – CLC Temperature Above 100 Degrees Celsius
CLC 524259.16 – CLC Temperature Above 85 Degrees Celsius
Group ECU: ECU Code Diagnostics
ECU 000094.03 – Low Pressure Fuel Signal Out of Range High
ECU 000094.04 – Low Pressure Fuel Signal Out of Range Low
ECU 000094.17 – Low Pressure Fuel Signal Slightly Low
ECU 000097.03 – Water In Fuel Signal Out of Range High
ECU 000097.04 – Water In Fuel Signal Out of Range Low
ECU 000097.16 – Water In Fuel Detected
ECU 000100.01 – Engine Oil Pressure Signal Extremely Low
ECU 000100.04 – Engine Oil Pressure Signal Out of Range Low
ECU 000100.18 – Engine Oil Pressure Signal Moderately Low
ECU 000100.31 – Engine Oil Pressure Invalid
ECU 000102.02 – Intake Manifold Pressure Signal Invalid
ECU 000102.03 – Intake Manifold Pressure Signal Out of Range High
ECU 000102.04 – Intake Manifold Pressure Signal Out of Range Low
ECU 000103.00 – Turbo Speed Signal Extremely High
ECU 000103.05 – Turbo Speed Sensor Circuit Has High Resistance
ECU 000103.06 – Turbo Speed Sensor Circuit Has Low Resistance
ECU 000103.08 – Turbocharger Speed Signal Incorrect
ECU 000103.31 – Turbocharger Speed Signal Missing
ECU 000105.00 – Intake Manifold Air Temperature Signal Extremely High
ECU 000105.03 – Intake Manifold Air Temperature Signal Out of Range High
ECU 000105.04 – Intake Manifold Air Temperature Signal Out of Range Low
ECU 000105.15 – Intake Manifold Air Temperature Signal Slightly High
ECU 000105.16 – Intake Manifold Air Temperature Signal Moderately High
ECU 000108.02 – Barometric Pressure Signal Invalid
ECU 000110.00 – Engine Coolant Temperature Signal Extremely High
ECU 000110.03 – Engine Coolant Temperature Signal Out of Range High
ECU 000110.04 – Engine Coolant Temperature Signal Out of Range Low
ECU 000110.15 – Engine Coolant Temperature Signal Slightly High
ECU 000110.16 – Engine Coolant Temperature Signal Moderately High
ECU 000110.17 – Engine Coolant Temperature Signal Slightly Low
ECU 000157.01 – High Pressure Fuel Signal Extremely Low
ECU 000157.03 – High Pressure Fuel Signal Out of Range High
ECU 000157.04 – High Pressure Fuel Signal Out of Range Low
ECU 000157.10 – Fuel Rail Pressure Loss Detected
ECU 000157.16 – High Pressure Fuel Signal Moderately High
ECU 000157.17 – Fuel Rail Pressure Not Developed
ECU 000157.18 – High-Pressure Fuel Signal Moderately Low
ECU 000158.17 – ECU Power Down Error
ECU 000174.00 – Fuel Temperature Signal Extremely High
ECU 000174.03 – Fuel Temperature Signal Out of Range High
ECU 000174.04 – Fuel Temperature Signal Out of Range Low
ECU 000174.16 – Fuel Temperature Signal Moderately High
ECU 000189.00 – Engine Speed Derate Condition Exists
ECU 000237.02 – VIN Security Data Invalid
ECU 000237.13 – VIN Option Code Security Data Conflict
ECU 000237.31 – VIN Security Data Missing
ECU 000412.00 – EGR Temperature Signal Extremely High
ECU 000412.03 – EGR Temperature Signal Out of Range High
ECU 000412.04 – EGR Temperature Signal Out of Range Low
ECU 000412.15 – EGR Temperature Signal Slightly High
ECU 000412.16 – EGR Temperature Signal Moderately High
ECU 000611.03 – Injector Shorted to Power
ECU 000611.04 – Injector Shorted to Ground
ECU 000627.01 – All Electronic Injector Currents Are Low
ECU 000629.12 – ECU EEPROM Error
ECU 000629.13 – ECU Programming Error
ECU 000636.02 – Camshaft Sensor Signal Invalid
ECU 000636.05 – Camshaft Sensor Circuit Has High Resistance
ECU 000636.06 – Camshaft Sensor Circuit Has Low Resistance
ECU 000636.08 – Camshaft Sensor Signal Missing
ECU 000636.10 – Camshaft Signal Rate of Change Abnormal
ECU 000637.02 – Crankshaft Position Sensor Signal Invalid
ECU 000637.05 – Crankshaft Position Sensor Circuit Has High Resistance
ECU 000637.06 – Engine Position Sensor Circuit Has Low Resistance
ECU 000637.07 – Crankshaft Position and Position Signals Out of Sync
ECU 000637.08 – Crankshaft Position Timing Sensor Signal Missing
ECU 000637.10 – Crankshaft Position Signal Rate of Change Abnormal
ECU 000640.11 – External Engine Protection Input
ECU 000640.31 – External Derate Commanded
ECU 000641.04 – VGT Actuator Supply Voltage Out of Range Low
ECU 000641.12 – VGT Actuator Communication Error
ECU 000641.13 – VGT Actuator Learn Error
ECU 000641.16 – Turbo Actuator Temperature Moderately High
ECU 000647.05 – Engine Fan Speed Increase Circuit Fault
ECU 000647.07 – Engine Fan Speed Decrease Circuit Fault
ECU 000651.02 – Injector #1 Part Data Invalid
ECU 000651.05 – Injector #1 Circuit Has High Resistance
ECU 000651.06 – Injector #1 Circuit Has Low Resistance
ECU 000651.07 – Injector #1 Not Responding
ECU 000651.13 – Injector #1 Calibration Fault
ECU 000652.02 – Injector #2 Part Data Invalid
ECU 000652.05 – Injector #2 Circuit Has High Resistance
ECU 000652.06 – Injector #2 Circuit Has Low Resistance
ECU 000652.07 – Injector #2 Not Responding
ECU 000652.13 – Injector #2 Calibration Fault
ECU 000653.02 – Injector #3 Part Data Invalid
ECU 000653.05 – Injector #3 Circuit Has High Resistance
ECU 000653.06 – Injector #3 Circuit Has Low Resistance
ECU 000653.07 – Injector #3 Not Responding
ECU 000653.13 – Injector #3 Calibration Fault
ECU 000654.02 – Injector #4 Part Data Invalid
ECU 000654.05 – Injector #4 Circuit Has High Resistance
ECU 000654.06 – Injector #4 Circuit Has Low Resistance
ECU 000654.07 – Injector #4 Not Responding
ECU 000654.13 – Injector #4 Calibration Fault
ECU 000655.02 – Injector #5 Part Data Invalid
ECU 000655.05 – Injector #5 Circuit Has High Resistance
ECU 000655.06 – Injector #5 Circuit Has Low Resistance
ECU 000655.07 – Injector #5 Not Responding
ECU 000655.13 – Injector #5 Calibration Fault
ECU 000656.02 – Injector #6 Part Data Invalid
ECU 000656.05 – Injector #6 Circuit Has High Resistance
ECU 000656.06 – Injector #6 Circuit Has Low Resistance
ECU 000656.07 – Injector #6 Not Responding
ECU 000656.13 – Injector #6 Calibration Fault
ECU 001075.05 – Low Pressure Fuel Pump Circuit Has High Resistance
ECU 001075.12 – Low Pressure Fuel Pump Status Error
ECU 001110.31 – Engine Protection Shutdown
ECU 001136.00 – ECU Temperature Signal Extremely High
ECU 001136.16 – ECU Temperature Signal Moderately High
ECU 001172.03 – Compressor Inlet Temperature Signal Out of Range High
ECU 001172.04 – Compressor Inlet Temperature Signal Out of Range Low
ECU 001180.00 – Turbine Inlet Temperature Signal Extremely High
ECU 001180.16 – Turbine Inlet Temperature Signal Moderately High
ECU 001347.03 – High Pressure Fuel Pump Control Valve Signal Out of Range High
ECU 001347.05 – High Pressure Fuel Pump Solenoid Circuit Has High Resistance
ECU 001347.07 – High Pressure Fuel Pump Not Able to Meet Required Rail Pressure
ECU 001569.31 – Engine in Power Derate Condition
ECU 001639.01 – Fan Speed Extremely Low
ECU 001639.16 – Fan Speed Moderately High
ECU 001639.18 – Fan Speed Moderately Low
ECU 002005.09 – ACU Message Missing
ECU 002005.14 – Communication Error
ECU 002005.19 – ACU Fault Message Received
ECU 002030.09 – VLC Message Missing
ECU 002071.09 – CCU Message Missing
ECU 002630.00 – Charge Air Cooler Outlet Temperature Signal Extremely High
ECU 002630.03 – Charge Air Cooler Outlet Temperature Signal Out of Range High
ECU 002630.04 – Charge Air Cooler Outlet Temperature Signal Out of Range Low
ECU 002630.15 – Charge Air Cooler Outlet Temperature Signal Slightly High
ECU 002630.16 – Charge Air Cooler Outlet Temperature Signal Moderately High
ECU 002659.02 – EGR Mass Flow Rate Data Invalid
ECU 002659.15 – EGR Mass Flow Rate Data Slightly High
ECU 002659.17 – EGR Mass Flow Rate Data Slightly Low
ECU 002790.16 – Calculated Turbine Outlet Temperature Moderately High
ECU 002791.02 – EGR Valve Position Signal Invalid
ECU 002791.03 – EGR Valve Position Signal Out of Range High
ECU 002791.04 – EGR Valve Position Signal Out of Range Low
ECU 002791.07 – EGR Valve Not Reaching Expected Position
ECU 002791.13 – EGR Valve Calibration Change Error
ECU 002791.31 – EGR Valve Calibration Change Over a Long Time
ECU 002795.07 – VGT Actuator Not Reaching Expected Position
ECU 003509.03 – Sensor Supply #1 Voltage Out of Range High
ECU 003509.04 – Sensor Supply #1 Voltage Out of Range Low
ECU 003510.03 – Sensor Supply #2 Voltage Out of Range High
ECU 003510.04 – Sensor Supply #2 Voltage Out of Range Low
ECU 003511.03 – Sensor Supply #3 Voltage Out of Range High
ECU 003511.04 – Sensor Supply #3 Voltage Out of Range Low
ECU 003512.03 – Sensor Supply #4 Voltage Out of Range High
ECU 003512.04 – Sensor Supply #4 Voltage Out of Range Low
ECU 003822.02 – EGR Valve Position Signal Invalid
ECU 003822.03 – EGR Valve Position Signal Out of Range High
ECU 003822.04 – EGR Valve Position Signal Out of Range Low
ECU 003822.07 – EGR Valve Not Reaching Expected Position
ECU 003822.13 – EGR Valve Calibration Change Error
ECU 003822.31 – EGR Valve Calibration Change Over a Long Time
Group FDH: FDH Code Diagnostics
FDH 517467.00 – FDH 5 V Sensor Supply Voltage High
FDH 517467.01 – FDH 5 V Sensor Supply Voltage Low
FDH 517467.02 – Proximity Sensor Circuit Fault
FDH 517467.03 – Proximity Sensor Voltage High
FDH 517467.04 – Proximity Sensor Voltage Low
FDH 517467.16 – Front Driveshaft Excessive Runout Fault
Group HCC: HCC Code Diagnostics
HCC 000158.04 – HCC Switched Supply Voltage Low
HCC 000168.04 – HCC Unswitched Supply Voltage Low
HCC 000190.02 – Rear Hitch Calibration Fault/Engine Speed Low
HCC 000629.12 – HCC Control Unit Fault
HCC 000630.13 – HCC Calibration Fault/Not Calibrated
HCC 001079.03 – HCC Sensor Supply Voltage High
HCC 001079.04 – HCC Sensor Supply Voltage Low
HCC 001638.02 – HCC Calibration Fault/Hydraulic Oil Temperature Low
HCC 001873.02 – Rear Hitch Position Sensor Circuit Voltage Fault
HCC 001873.03 – Rear Hitch Position Sensor Circuit Voltage High
HCC 001873.04 – Rear Hitch Position Sensor Circuit Voltage Low
HCC 001873.11 – Rear Hitch Position Restricted During Calibration
HCC 001873.13 – HCC Calibration Fault/Rear Hitch Position Sensor Circuit
HCC 001881.03 – Rear Hitch Draft Sensor Circuit Voltage High
HCC 001881.04 – Rear Hitch Draft Sensor Circuit Voltage Low
HCC 001881.13 – HCC Calibration Fault/Rear Hitch Draft Sensor Circuit
HCC 002005.09 – ACU Message Missing
HCC 002071.09 – CCU Message Missing
HCC 002152.09 – HV I Message Missing
HCC 002602.18 – Hydraulic Oil Level Low
HCC 521000.02 – Rear Hitch External Switch Circuit Fault
HCC 521000.31 – Rear Hitch External Switch Circuit Conflict
HCC 521001.02 – HCC Calibration Fault/Rear Hitch Pressure Valve Gain
HCC 523652.02 – Wire Connector Fault/Incompatible Harness Location
HCC 523788.02 – Hydraulic Option Configuration Changed Since Power-up
HCC 523788.14 – Hydraulic Option Configuration Change Not Allowed
HCC 523910.02 – HCC Control Unit Fault
HCC 523950.13 – Rear Hitch Calibration not Performed Correctly
HCC 523952.31 – Rear Hitch Disabled/HCC Configuration
HCC 524016.04 – HCC Switched Supply Voltage Low/Rear Hitch Solenoids
HCC 524212.19 – Rear Hitch Control Lever Fault Message Received
HCC 524212.31 – Rear Hitch Lever Command Missing
Group HCU: HCU Code Diagnostics
HCU 000158.04 – HCU Switched Supply Voltage Low
HCU 000168.04 – HCU Unswitched Supply Voltage Low
HCU 000190.02 – Rear Hitch Calibration Fault/Engine Speed Low
HCU 000629.12 – HCU Control Unit Fault
HCU 000630.13 – HCU Calibration Fault/Not Calibrated
HCU 000639.12 – HCU CAN Message Overflow
HCU 000639.14 – HCU CAN Error Limit Exceeded
HCU 001079.03 – HCU Sensor Supply Voltage High
HCU 001079.04 – HCU Sensor Supply Voltage Low
HCU 001638.02 – HCU Calibration Fault/Hydraulic Oil Temperature Low
HCU 001873.02 – Rear Hitch Position Sensor Circuit Voltage Fault
HCU 001873.03 – Rear Hitch Position Sensor Circuit Voltage High
HCU 001873.04 – Rear Hitch Position Sensor Circuit Voltage Low
HCU 001873.11 – Rear Hitch Position Sensor Fault
HCU 001873.13 – HCU Calibration Fault/Rear Hitch Position Sensor Circuit
HCU 001881.03 – Rear Hitch Draft Sensor Circuit Voltage High
HCU 001881.04 – Rear Hitch Draft Sensor Circuit Voltage Low
HCU 001881.13 – HCU Calibration Fault/Rear Hitch Draft Sensor Circuit
HCU 002005.09 – ACU Message Missing
HCU 002071.09 – CCU Message Missing
HCU 002602.18 – Hydraulic Oil Level Low
HCU 521000.02 – Rear Hitch External Switch Circuit Fault
HCU 521000.31 – Rear Hitch External Switch Circuit Fault
HCU 521001.02 – HCU Calibration Fault/Rear Hitch Pressure Valve Gain
HCU 521001.05 – Rear Hitch Pressure Solenoid Current Low
HCU 521001.06 – Rear Hitch Pressure Solenoid Current High
HCU 521001.07 – HCU Calibration Fault/Rear Hitch Pressure Valve
HCU 521001.11 – HCU Calibration Fault/Rear Hitch Pressure Valve
HCU 521001.13 – Rear Hitch Raise Valve not Calibrated
HCU 521002.05 – Rear Hitch Return Solenoid Current Low
HCU 521002.06 – Rear Hitch Return Solenoid Current High
HCU 521002.07 – HCU Calibration Fault/Rear Hitch Return Valve
HCU 521002.11 – HCU Calibration Fault/Rear Hitch Return Valve
HCU 521002.13 – Rear Hitch Lower Valve Not Calibrated
HCU 523652.02 – Wire Connector Fault
HCU 523788.02 – Hydraulic Option Configuration Changed Since Power-up
HCU 523788.14 – Hydraulic Option Configuration Change Not Allowed
HCU 523910.02 – HCU Control Unit Fault
HCU 523950.13 – Hitch Calibration Purge Counting Fault
HCU 523952.31 – Rear Hitch Disabled/HCU Configuration
HCU 524016.04 – HCU Switched Supply Voltage Low/Rear Hitch Solenoids
HCU 524212.19 – Rear Hitch Control Lever Fault Message Received
HCU 524212.31 – Rear Hitch Lever Command Missing
Group HV1: HV1 Code Diagnostics
HV1 000158.03 – HV I Switched Supply Voltage High
HV1 000158.04 – HV I Switched Supply Voltage Low
HV1 002035.09 – HCC Message Missing
HV1 004084.07 – HV I Not in FLOAT Position
HV1 004084.16 – HV I Overshot Commanded Position
HV1 004084.18 – HV I Failed to Reach Commanded Position
HV1 004085.07 – HV I Not in NEUTRAL Position
HV1 004085.12 – HV1 Control Unit Fault
Group ICU: ICU Code Diagnostics
ICU 000237.02 – VIN Security Data Conflict
ICU 000237.14 – VIN Security Not Enabled
ICU 000237.31 – VIN Security Messages Missing
ICU 000251.12 – ICU Clock Fault
ICU 000628.12 – ICU Programming
ICU 000629.09 – Cornerpost Display Message Missing
ICU 000629.12 – ICU Control Unit Fault
ICU 000630.02 – ICU Calibration Fault/Data Invalid
ICU 002000.09 – ECU Message Missing
ICU 002003.09 – PTI or PTQ Message Missing
ICU 002005.09 – ACU Message Missing
ICU 002011.09 – BRC Message Missing
ICU 002019.09 – SSU Message Missing
ICU 002025.09 – ATC Message Missing
ICU 002030.09 – VLC Message Missing
ICU 002034.09 – SCU Message Missing
ICU 002035.09 – HCU Message Missing
ICU 002049.09 – CAB Message Missing
ICU 002050.09 – CLC Message Missing
ICU 002054.09 – ASU Message Missing
ICU 002071.09 – CCU Message Missing
ICU 002129.09 – ICU Message Missing
ICU 002213.09 – SCO Message Missing
ICU 002227.09 – SUP Message Missing
ICU 002240.09 – TEC Message Missing
ICU 002255.09 – CAN Bus Fault
ICU 517467.09 – FDH Message Missing
ICU 524013.03 – ICU Switch Fault
Group PTP: PTP Code Diagnostics
PTP Code Diagnostics
Group SCC: SCC Code Diagnostics
SCC 000158.04 – SCC Switched Supply Voltage Low
SCC 000168.03 – SCC Unswitched Supply Voltage High
SCC 000168.04 – SCC Unswitched Supply Voltage Low
SCC 000629.12 – SCC Control Unit Fault
SCC 000630.13 – SCC Calibration Fault/Not Calibrated
SCC 000639.12 – SCC CAN Message Overflow
SCC 000639.14 – SCC CAN Error Limit Exceeded
SCC 001079.03 – SCC Sensor Supply Voltage High
SCC 001079.04 – SCC Sensor Supply Voltage Low
SCC 002005.09 – ACU Message Missing
SCC 002049.09 – CAB Message Missing
SCC 002071.09 – CCU Message Missing
SCC 002161.09 – SV I Message Missing
SCC 002162.09 – SV II Message Missing
SCC 002163.09 – SV III Message Missing
SCC 002164.09 – SV IV Message Missing
SCC 002165.09 – SV V Message Missing
SCC 002166.09 – SV VI Message Missing
SCC 002602.18 – Hydraulic Oil Level Low
SCC 523216.03 – SCC Unswitched Supply Voltage High to SV I and SV II
SCC 523216.04 – SCC Unswitched Supply Voltage Low to SV I and SV II
SCC 523219.03 – SCC Unswitched Supply Voltage High to SV III and SV IV
SCC 523219.04 – SCC Unswitched Supply Voltage Low to SV III and SV IV
SCC 523652.02 – Wire Connector Fault
SCC 523693.02 – Missing SV I External Control Message for 10 Seconds
SCC 523693.09 – Missing SV I External Control Message for 1 Second
SCC 523693.19 – SV I External Control Fault Message Received
SCC 523694.02 – Missing SV II External Control Message for 10 Seconds
SCC 523694.09 – Missing SV II External Control Message for 1 Second
SCC 523694.19 – SV II External Control Fault Message Received
SCC 523695.02 – Missing SV V External Control Message for 10 Seconds
SCC 523695.09 – Missing SV V External Control Message for 1 Second
SCC 523695.19 – SV V External Control Fault Message Received
SCC 523696.02 – Missing SV VI External Control Message for 10 Seconds
SCC 523696.09 – SV VI External Control Message Rate Fault
SCC 523696.19 – SV VI External Control Fault Message Received
SCC 523775.19 – Single Lever Control Hand Presence Switch Fault Message Received
SCC 523776.19 – Single Lever Control Transport Lock Switch Fault Message Received
SCC 523785.01 – Lost Laser Track/Electro-Hydraulic External Control Not Available for SV III
SCC 523785.03 – SVs I—IV Remote Position Sensor 2 Circuit Voltage High
SCC 523785.04 – SVs I—IV Remote Position Sensor 2 Circuit Voltage Low
SCC 523785.07 – SVs I—IV Remote Position Sensor 2 Fault/Unexpected Response
SCC 523786.01 – Lost Laser Track/Electro-Hydraulic External Control Not Available for SV I
SCC 523786.03 – SVs I—IV Remote Position Sensor 1 Circuit Voltage High
SCC 523786.04 – SVs I—IV Remote Position Sensor 1 Circuit Voltage Low
SCC 523786.07 – SVs I—IV Remote Position Sensor 1 Fault/Unexpected Response
SCC 523788.02 – Hydraulic Option Configuration Changed Since Power-Up
SCC 523788.14 – Hydraulic Option Configuration Changed Without Disconnect
SCC 523788.31 – Hydraulic Option Configuration Invalid
SCC 523801.19 – Single Lever Control Auxiliary Switch Fault Message Received
SCC 523804.19 – Single Lever Control Lateral Sensor Fault Message Received
SCC 523805.19 – Single Lever Control Fore-Aft Sensor Fault Message Received
SCC 523910.02 – SCC Control Unit Fault
SCC 523923.19 – SCV I Control Lever Fault Message Received
SCC 523923.31 – SCV I Control Lever Command Missing
SCC 523942.31 – Operator Out of Seat With SV VI ON
SCC 523943.31 – Operator Out of Seat With SV V ON
SCC 523944.31 – Operator Out of Seat With SV IV ON
SCC 523945.31 – Operator Out of Seat With SV III ON
SCC 523946.31 – Operator Out of Seat With SV II ON
SCC 523947.31 – Operator Out of Seat With SV I ON
SCC 524015.02 – Missing SV III External Control Message for 10 Seconds
SCC 524015.09 – Missing SV III External Control Message for 1 Second
SCC 524015.19 – SV III External Control Fault Message Received
SCC 524038.19 – SV IV External Control Fault Message Received
SCC 524101.19 – SCV VI Control Lever Fault Message Received
SCC 524101.31 – SV VI Lever Command Missing
SCC 524102.19 – SCV V Control Lever Fault Message Received
SCC 524102.31 – SCV V Control Lever Command Missing
SCC 524103.19 – SCV IV Control Lever Fault Message Received
SCC 524103.31 – SCV IV Control Lever Command Missing
SCC 524104.19 – SCV III Control Lever Fault Message Received
SCC 524104.31 – SCV III Control Lever Command Missing
SCC 524105.19 – SCV II Control Lever Fault Message Received
SCC 524105.31 – SCV II Control Lever Command Missing
Group SCO: SCO Code Diagnostics
SCO 000158.04 – SCO Switched Supply Voltage Low
SCO 000168.04 – SCO Unswitched Supply Voltage Low
SCO 000629.12 – SCO Control Unit Fault
SCO 000630.02 – SCO Calibration Fault/Data Invalid
SCO 000630.13 – SCO Calibration Fault/Not Calibrated
SCO 000639.12 – SCO CAN Message Overflow
SCO 000639.14 – SCO CAN Error Limit Exceeded
SCO 001638.02 – SCO Calibration Fault/Hydraulic Oil Temperature Low
SCO 001961.13 – SCO Calibration Fault/SCV V Extend Not Calibrated
SCO 001962.13 – SCO Calibration Fault/SCV V Retract Not Calibrated
SCO 001963.05 – SCV V Flow Control Solenoid Current Low for Float Operation
SCO 001973.13 – SCO Calibration Fault/SCV VI Extend Not Calibrated
SCO 001974.13 – SCO Calibration Fault/SCV VI Retract Not Calibrated
SCO 001975.05 – SCV VI Flow Control Solenoid Current Low for Float Operation
SCO 002005.09 – ACU Message Missing
SCO 002071.09 – CCU Message Missing
SCO 002602.18 – Hydraulic Oil Level Low
SCO 523652.02 – Wire Connector Fault
SCO 523695.02 – Missing SCV V External Control Message for 10 Seconds
SCO 523695.09 – SCV V External Control Lever Message Rate Fault
SCO 523695.19 – SCV V External Control Lever Fault Message Received
SCO 523696.02 – Missing SCV VI External Control Message for 10 Seconds
SCO 523696.09 – SCV VI External Control Lever Message Rate Fault
SCO 523696.19 – SCV VI External Control Lever Fault Message Received
SCO 523910.02 – SCO Control Unit Fault
SCO 523930.05 – SCV VI Extend Solenoid Circuit Current Low
SCO 523930.06 – SCV VI Extend Solenoid Circuit Current High
SCO 523931.05 – SCV V Extend Solenoid Circuit Current Low
SCO 523931.06 – SCV V Extend Solenoid Circuit Current High
SCO 523936.05 – SCV VI Retract Solenoid Circuit Current Low
SCO 523936.06 – SCV VI Retract Solenoid Circuit Current High
SCO 523937.05 – SCV V Retract Solenoid Circuit Current Low
SCO 523937.06 – SCV V Retract Solenoid Circuit Current High
SCO 523942.31 – Operator Out Of Seat With SCV VI On
SCO 523943.31 – Operator Out Of Seat With SCV V On
SCO 524016.03 – SCO Switched Supply Voltage High/SCV V and SCV VI Solenoids
SCO 524016.04 – SCO Switched Supply Voltage Low/SCV V and SCV VI Solenoids
SCO 524101.19 – SCV VI Control Lever Fault Message Received
SCO 524101.31 – SCV VI Control Lever Command Missing
SCO 524102.19 – SCV V Control Lever Fault Message Received
SCO 524102.31 – SCV V Control Lever Command Missing
Group SCU: SCU Code Diagnostics
SCU 000158.04 – SCU Switched Supply 1 Voltage Low
SCU 000168.04 – SCU Unswitched Supply Voltage Low
SCU 000523.19 – Transmission Gear Status Fault Message Received
SCU 000523.31 – Transmission Gear Status Message Missing
SCU 000629.12 – SCU Control Unit Fault
SCU 000630.02 – SCU Calibration Fault/Data Invalid
SCU 000630.13 – SCU Calibration Fault/Not Calibrated
SCU 000639.12 – SCU CAN Message Overflow
SCU 000639.14 – SCU CAN Error Limit Exceeded
SCU 001079.03 – SCU Sensor Supply Voltage High
SCU 001079.04 – SCU Sensor Supply Voltage Low
SCU 001638.02 – SCU Calibration Fault/Hydraulic Oil Temperature Low
SCU 001859.19 – Radar Message Reporting an Error
SCU 001859.31 – Radar Information Unavailable
SCU 001913.13 – SCU Calibration Fault/SCV I Extend Not Calibrated
SCU 001914.13 – SCU Calibration Fault/SCV I Retract Not Calibrated
SCU 001915.05 – SCV I Flow Control Solenoid Current Low for Float Operation
SCU 001925.13 – SCU Calibration Fault/SCV II Extend Not Calibrated
SCU 001926.13 – SCU Calibration Fault/SCV II Retract Not Calibrated
SCU 001927.05 – SCV II Flow Control Solenoid Current Low for Float Operation
SCU 001937.13 – SCU Calibration Fault/SCV III Extend Not Calibrated
SCU 001938.13 – SCU Calibration Fault/SCV III Retract Not Calibrated
SCU 001939.05 – SCV III Flow Control Solenoid Current Low for Float Operation
SCU 001949.13 – SCU Calibration Fault/SCV IV Extend Not Calibrated
SCU 001950.13 – SCU Calibration Fault/SCV IV Retract Not Calibrated
SCU 001951.05 – SCV IV Flow Control Solenoid Current Low for Float Operation
SCU 001961.13 – SCU Calibration Fault/SCV V Extend Not Calibrated (Scraper Only 10000-)
SCU 001962.13 – SCU Calibration Fault/SCV V Retract Not Calibrated (Scraper Only 10000-)
SCU 001963.05 – SCV V Flow Control Solenoid Current Low for Float Operation (Scraper Only 10000-)
SCU 001973.13 – SCU Calibration Fault/SCV VI Extend Not Calibrated (Scraper Only 10000-)
SCU 001974.13 – SCU Calibration Fault/SCV VI Retract Not Calibrated (Scraper Only 10000-)
SCU 001975.05 – SCV VI Flow Control Solenoid Current Low for Float Operation (Scraper Only 10000-)
SCU 002003.09 – PTP Message Missing
SCU 002005.09 – ACU Message Missing
SCU 002049.09 – CAB Message Missing
SCU 002071.09 – CCU Message Missing
SCU002129.09 – ICU Message Missing
SCU 002602.18 – Hydraulic Oil Level Low
SCU 523216.03 – SCU Valve Supply 4 Voltage High
SCU 523216.04 – SCU Valve 4 Voltage Low
SCU 523219.03 – SCU Valve Supply 1 Voltage High
SCU 523219.04 – SCU Valve 1 Voltage Low
SCU 523652.02 – Wire Connector Fault
SCU 523693.02 – Missing SCV I External Control Message for 10 Seconds
SCU 523693.09 – Missing SCV I External Control Message for 1 Second
SCU 523693.19 – SCV I External Control Fault Message Received
SCU 523694.02 – Missing SCV II External Control Message for 10 Seconds
SCU 523694.09 – Missing SCV II External Control Message for 1 Second
SCU 523694.19 – SCV II External Control Fault Message Received
SCU 523695.02 – Missing SCV V External Control Message for 10 Seconds (Scraper Only 10000-)
SCU 523695.09 – SCV V External Control Lever Message Rate Fault (Scraper Only 10000-)
SCU 523695.19 – SCV V External Control Lever Fault Message Received (Scraper Only 10000-)
SCU 523696.02 – Missing SCV VI External Control Message for 10 Seconds (Scraper Only 10000-)
SCU 523696.09 – SCV VI External Control Lever Message Rate Fault (Scraper Only 10000-)
SCU 523696.19 – SCV VI External Control Lever Fault Message Received (Scraper Only 10000-)
SCU 523775.19 – Single Lever Control Hand Presence Switch Fault Message Received
SCU 523776.19 – Single Lever Control Transport Lock Switch Fault Message Received
SCU 523783.03 – SCVs I – IV Remote Position Sensor 4 Circuit Voltage High
SCU 523783.04 – SCVs I – IV Remote Position Sensor 4 Circuit Voltage Low
SCU 523783.07 – SCVs I – IV Remote Position Sensor 4 Fault/Unexpected Response
SCU 523784.03 – SCVs I – IV Remote Position Sensor 3 Circuit Voltage High
SCU 523784.04 – SCVs I – IV Remote Position Sensor 3 Circuit Voltage Low
SCU 523784.07 – SCVs I – IV Remote Position Sensor 3 Fault/Unexpected Response
SCU 523784.13 – SCVs I – IV Remote Position Sensor 3 Calibration Fault
SCU 523785.01 – SCU – Deluxe Hydraulic Control Unit – Auxiliary Valve Control
SCU 523785.03 – SCVs I – IV Remote Position Sensor 2 Circuit Voltage High
SCU 523785.04 – SCVs I – IV Remote Position Sensor 2 Circuit Voltage Low
SCU 523785.07 – SCVs I – IV Remote Position Sensor 2 Fault/Unexpected Response
SCU 523785.13 – SCVs I – IV Remote Position Sensor 2 Setpoint Fault
SCU 523786.01 – SCU – Deluxe Hydraulic Control Unit – Auxiliary Valve Control
SCU 523786.03 – SCVs I – IV Remote Position Sensor 1 Circuit Voltage High
SCU 523786.04 – SCVs I – IV Remote Position Sensor 1 Circuit Voltage Low
SCU 523786.07 – SCVs I – IV Remote Position Sensor 1 Fault/Unexpected Response
SCU 523786.13 – SCVs I – IV Remote Position Sensor 1 Setpoint Fault
SCU 523787.03 – SCU Switched Supply Voltage High/SCVs III and IV Solenoids
SCU 523787.04 – SCU Switched Supply Voltage Low/SCVs III and IV Solenoids
SCU 523788.02 – Hydraulic Option Configuration Changed Since Power-Up
SCU 523788.14 – Hydraulic Option Configuration Changed Without Disconnect
SCU 523788.31 – Hydraulic Option Configuration Invalid
SCU 523804.19 – Single Lever Control Lateral Sensor Fault Message Received
SCU 523805.19 – Single Lever Control Fore-Aft Sensor Fault Message Received
SCU 523910.02 – SCU Control Unit Fault
SCU 523923.19 – SCV I Control Lever Fault Message Received
SCU 523923.31 – SCV I Control Lever Command Missing
SCU 523930.05 – SCV VI Extend Solenoid Circuit Current Low (Scraper Only 10000-)
SCU 523930.06 – SCV VI Extend Solenoid Circuit Current High (Scraper Only 10000-)
SCU 523931.05 – SCV V Extend Solenoid Circuit Current Low (Scraper Only 10000-)
SCU 523931.06 – SCV V Extend Solenoid Circuit Current High (Scraper Only 10000-)
SCU 523932.05 – SCV IV Extend Solenoid Circuit Current Low
SCU 523932.06 – SCV IV Extend Solenoid Circuit Current High
SCU 523933.05 – SCV III Extend Solenoid Circuit Current Low
SCU 523933.06 – SCV III Extend Solenoid Circuit Current High
SCU 523934.05 – SCV II Extend Solenoid Circuit Current Low
SCU 523934.06 – SCV II Extend Solenoid Circuit Current High
SCU 523935.05 – SCV I Extend Solenoid Circuit Current Low
SCU 523935.06 – SCV I Extend Solenoid Circuit Current High
SCU 523936.05 – SCV VI Retract Solenoid Circuit Current Low (Scraper Only 10000-)
SCU 523936.06 – SCV VI Retract Solenoid Circuit Current High (Scraper Only 10000-)
SCU 523937.05 – SCV V Retract Solenoid Circuit Current Low (Scraper Only 10000-)
SCU 523937.06 – SCV V Retract Solenoid Circuit Current High (Scraper Only 10000-)
SCU 523938.05 – SCV IV Retract Solenoid Circuit Current Low
SCU 523938.06 – SCV IV Retract Solenoid Circuit Current High
SCU 523939.05 – SCV III Retract Solenoid Circuit Current Low
SCU 523939.06 – SCV III Retract Solenoid Circuit Current High
SCU 523940.05 – SCV II Retract Solenoid Circuit Current Low
SCU 523940.06 – SCV II Retract Solenoid Circuit Current High
SCU 523941.05 – SCV I Retract Solenoid Circuit Current Low
SCU 523941.06 – SCV I Retract Solenoid Circuit Current High
SCU 523942.31 – Operator Out Of Seat With SCV VI On (Scraper Only 10000-)
SCU 523943.31 – Operator Out Of Seat With SCV V On (Scraper Only 10000-)
SCU 523944.31 – Operator Out Of Seat With SCV IV On
SCU 523945.31 – Operator Out Of Seat With SCV III On
SCU 523946.31 – Operator Out Of Seat With SCV II On
SCU 523947.31 – Operator Out Of Seat With SCV I On
SCU 524015.02 – Missing SCV III External Control Message for 10 Seconds
SCU 524015.09 – Missing SCV III External Control Message for 1 Second
SCU 524015.19 – SCV III External Control Fault Message Received
SCU 524016.03 – SCU Switched Supply Voltage High/SCVs I and II Solenoids
SCU 524016.04 – SCU Switched Supply Voltage Low/SCV I and II Solenoids
SCU 524038.02 – Missing SCV IV External Control Message for 10 Seconds
SCU 524038.09 – Missing SCV IV External Control Message for 1 Second
SCU 524038.19 – SCV IV External Control Lever Fault Message Received
SCU 524096.19 – Hand Throttle Position Fault Message Received
SCU 524096.31 – Hand Throttle Position Message Missing
SCU 524101.19 – SCV VI Control Lever Fault Message Received (Scraper Only 10000-)
SCU 524101.31 – SCV VI Control Lever Command Missing (Scraper Only 10000-)
SCU 524102.19 – SCV V Control Lever Fault Message Received (Scraper Only 10000-)
SCU 524102.31 – SCV V Control Lever Command Missing (Scraper Only 10000-)
SCU 524103.19 – SCV IV Control Lever Fault Message Received
SCU 524103.31 – SCV IV Control Lever Command Missing
SCU 524104.19 – SCV III Control Lever Fault Message Received
SCU 524104.31 – SCV III Control Lever Command Missing
SCU 524105.19 – SCV II Control Lever Fault Message Received
SCU 524105.31 – SCV II Control Lever Command Missing
SCU 524173.19 – Clutch Pedal Position Fault Message Received
SCU 524173.31 – Clutch Pedal Position Message Missing
Group SSU: SSU Code Diagnostics
SSU 000084.09 – Wheel Speed Message Missing
SSU 000168.03 – Steering System Control Unit (SSU) Unswitched Supply Voltage High
SSU 000168.04 – Steering System Control Unit (SSU) Unswitched Supply Voltage Low
SSU 000177.09 – Hydraulic Oil Temperature Message Missing
SSU 000237.31 – Vehicle Identification Number (VIN) Security Message Missing
SSU 000517.09 – GPS Speed Message Missing
SSU 000523.09 – MST Current Gear Message Missing
SSU 000523.31 – Transmission Message Missing
SSU 000524.09 – Selected Gear Message Missing
SSU 000628.02 – Steering System Control Unit (SSU) End Of Line (EOL) Data Fault
SSU 000628.12 – Steering System Control Unit (SSU) Programming
SSU 000629.12 – Steering System Control Unit (SSU) Fault
SSU 000630.13 – Steering System Control Unit (SSU) Calibration Fault / Not Calibrated
SSU 001079.03 – Steering System Control Unit (SSU) Steer Angle Sensor Supply Voltage High
SSU 001079.04 – Steering System Control Unit (SSU) Steer Angle Sensor Supply Voltage Low
SSU 001504.09 – Operator Presence Message Missing
SSU 001504.14 – Operator Not Seated While AutoTrac Active
SSU 001638.09 – Hydraulic Oil Temperature Message Missing
SSU 001807.02 – Steering Wheel Position Sensors Conflict
SSU 001807.03 – Steering Wheel Position Sensor 1 Supply Voltage High
SSU 001807.04 – Steering Wheel Position Sensor 1 Supply Voltage Low
SSU 001807.05 – Steering Wheel Position Sensor 1 Circuit Current Low
SSU 001807.06 – Steering Wheel Position Sensor 1 Circuit Current High
SSU 001807.10 – Steering Wheel Position Sensor 1 Signal Mismatch
SSU 001807.14 – Steering Wheel Position Sensor 1 Signal Fault
SSU 001865.09 – ELX Message Missing
SSU 522273.00 – Electro-Hydraulic Steering Valve Control Circuit Command High
SSU 522273.01 – Electro-Hydraulic Steering Valve Control Circuit Command Low
SSU 522387.07 – Steering Angle Sensor Or Electro-Hydraulic Steering Valve Fault
SSU 522394.09 – Terrain Compensation Module (TCM) Message Missing
SSU 522451.00 – Steering Angle Sensor (Secondary) Signal High
SSU 522451.01 – Steering Angle Sensor (Secondary) Signal Low
SSU 522451.14 – Steering Angle Sensor (Secondary) Voltage Fault
SSU 523651.02 – Steering System Control Unit (SSU) Fault
SSU 523698.09 – GreenStar Display Message Missing
SSU 523767.09 – Resume Switch Message Missing
SSU 523795.02 – Electro-Hydraulic Steering Valve Work Port Connections Backwards
SSU 523795.11 – Electro-Hydraulic Steering Valve Deadband Inconsistent
SSU 523795.12 – Electro-Hydraulic Steering Valve Fault
SSU 523795.13 – Steering System Control Unit (SSU) Calibration Fault/Electro-Hydraulic Steering Valve
SSU 523810.00 – Electro-Hydraulic Steering Valve Supply Voltage High
SSU 523810.01 – Electro-Hydraulic Steering Valve Supply Voltage Low
SSU 523821.02 – Vehicle Mismatch
SSU 523824.03 – Steering Wheel Position Sensor 2 Supply Voltage High
SSU 523824.04 – Steering Wheel Position Sensor 2 Supply Voltage Low
SSU 523824.05 – Steering Wheel Position Sensor 2 Circuit Current Low
SSU 523824.06 – Steering Wheel Position Sensor 2 Circuit Current High
SSU 523824.10 – Steering Wheel Position Sensor 2 Signal Mismatch
SSU 523824.14 – Steering Wheel Position Sensor 2 Signal Fault
SSU 523826.00 – Steering Angle Sensor (Primary) Signal High
SSU 523826.01 – Steering Angle Sensor (Primary) Signal Low
SSU 523826.02 – SSU Calibration Fault / Steering Angle Sensor (Primary) Polarity Reversed
SSU 523826.07 – Steering Angle Sensor (Primary) Fault / No Steered Motion
SSU 523826.10 – SAS (Primary) Fault / Steered Motion Detected Without Steering Wheel Motion
SSU 523826.12 – Steering Angle Sensor Voltage Deadband
SSU 523826.14 – SAS (Primary) Fault / Steering Wheel Motion Detected Without Steered Motion
SSU 524221.09 – Vehicle Yaw Rate Message Missing
Group SUP: SUP Code Diagnostics
SUP 000628.12 – SUP Programming
SUP 000629.12 – SUP Control Unit Fault
SUP 524013.03 – SUP Switch Fault
Group SV1: SV1 Code Diagnostics
SV1 000158.03 – SV I Switched Supply Voltage High
SV1 000158.04 – SV I Switched Supply Voltage Low
SV1 002034.09 – SCC Message Missing
SV1 004084.07 – SV I Not in Float Position
SV1 004084.16 – SV I Overshot Commanded Position
SV1 004084.18 – SV I Failed to Reach Commanded Position
SV1 004085.07 – SV I Not in NEUTRAL Position
SV1 004085.12 – SV1 Control Unit Fault
Group SV2: SV2 Code Diagnostics
SV2 000158.03 – SV II Switched Supply Voltage High
SV2 000158.04 – SV II Switched Supply Voltage Low
SV2 002034.09 – SCC Message Missing
SV2 004084.07 – SV II Not in Float Position
SV2 004084.16 – SV II Overshot Commanded Position
SV2 004084.18 – SV II Failed to Reach Commanded Position
SV2 004085.07 – SV II Not in Neutral Position
SV2 004085.12 – SV2 Control Unit Fault
Group SV3: SV3 Code Diagnostics
SV3 000158.03 – SV III Switched Supply Voltage High
SV3 000158.04 – SV III Switched Supply Voltage Low
SV3 002034.09 – SCC Message Missing
SV3 004084.07 – SV III Not in Float Position
SV3 004084.16 – SV III Overshot Commanded Position
SV3 004084.18 – SV III Failed to Reach Commanded Position
SV3 004085.07 – SV III Not in Neutral Position
SV3 004085.12 – SV3 Control Unit Fault
Group SV4: SV4 Code Diagnostics
SV4 000158.03 – SV IV Switched Supply Voltage High
SV4 000158.04 – SV IV Switched Supply Voltage Low
SV4 002034.09 – SCC Message Missing
SV4 004084.07 – SV IV Not in Float Position
SV4 004084.16 – SV IV Overshot Commanded Position
SV4 004084.18 – SV IV Failed to Reach Commanded Position
SV4 004085.07 – SV IV Not in Neutral Position
SV4 004085.12 – SV4 Control Unit Fault
Group SV5: SV5 Code Diagnostics
SV5 000158.03 – SV V Switched Supply Voltage High
SV5 000158.04 – SV V Switched Supply Voltage Low
SV5 002034.09 – SCC Message Missing
SV5 004084.07 – SV V Not in Float Position
SV5 004084.16 – SV V Overshot Commanded Position
SV5 004084.18 – SV V Failed to Reach Commanded Position
SV5 004085.07 – SV V Not in Neutral Position
SV5 004085.12 – SV5 Control Unit Fault
Group SV6: SV6 Code Diagnostics
SV6 000158.03 – SV VI Switched Supply Voltage High
SV6 000158.04 – SV VI Switched Supply Voltage Low
SV6 002034.09 – SCC Message Missing
SV6 004084.07 – SV VI Not in Float Position
SV6 004084.16 – SV VI Overshot Commanded Position
SV6 004084.18 – SV VI Failed to Reach Commanded Position
SV6 004085.07 – SV VI Not in Neutral Position
SV6 004085.12 – SV6 Control Unit Fault
Group TEC: TEC Code Diagnostics
TEC 000628.12 – Tractor Equipment Control Unit (TEC) Programming
TEC 000630.02 – Tractor Equipment Control Unit (TEC) Calibration Fault / Data Invalid
TEC 522550.14 – ISO Compliant and Non-ISO Compliant Devices on Implement Bus
Group VLC: VLC Code Diagnostics
VLC 000628.02 – Vehicle Load Center (VLC) End Of Line Data Fault
VLC 000628.12 – Vehicle Load Center (VLC) Programming
VLC 000629.11 – Vehicle Load Center (VLC) Control Unit Fault
VLC 000629.12 – Vehicle Load Center (VLC) Control Unit Fault
VLC 001542.04 – Vehicle Load Center (VLC) Control Unit Wake-Up Signal Voltage Low
VLC 001550.05 – A/C Compressor Clutch Circuit Current Low
VLC 001550.06 – A/C Compressor Clutch Circuit Current High
VLC 002030.06 – Vehicle Load Center (VLC) Circuit Current High
VLC 002050.09 – Cab Load Center (CLC) Control Unit Message Missing
VLC 002348.05 – High Beam Lights Circuit Current Low
VLC 002348.06 – High Beam Lights Circuit Current High
VLC 002350.05 – Low Beam Lights Circuit Current Low
VLC 002350.06 – Low Beam Lights Circuit Current High
VLC 002354.05 – Front Outer Flood Lights Circuit Current Low
VLC 002354.06 – Front Outer Flood Lights Circuit Current High
VLC 002356.05 – Front Inner Flood Lights Circuit Current Low
VLC 002356.06 – Front Inner Flood Lights Circuit Current High
VLC 002388.05 – Center Spot Light Circuit Current Low
VLC 002388.06 – Center Spot Light Circuit Current High
VLC 522310.06 – ELX Output 2 Circuit Current High
VLC 522311.05 – Rear Washer Pump Circuit Current Low
VLC 522311.06 – Rear Washer Pump Circuit Current High
VLC 522312.05 – Front Washer Pump Circuit Current Low
VLC 522312.06 – Front Washer Pump Circuit Current High
VLC 522620.05 – Horn Circuit Current Low
VLC 522620.06 – Horn Circuit Current High
Section 212: OBSERVABLE SYMPTOMS
Group 20: Engines
Engine Electrical Diagnostics
Group 30: Fuel and Air
Fuel and Air Electrical Diagnostics
Group 40: Electrical
AutoLoad™ Display Diagnostics
AutoLoad™ EMI Diagnostics
AutoLoad™ Performance Diagnostics
Charging System Diagnostics
Control Unit System Diagnostics
Electrical Connector Diagnostics
Lighting System Diagnostics
Starting System Diagnostics
Group 45: Control Units
Armrest Control Unit (ACU) Diagnostics
Automatic Temperature Control (ATC) Control Unit Diagnostics
Brake Control Unit (BRC) Diagnostics
CAB Control Unit Diagnostics
Cab Load Center (CLC) Control Unit Diagnostics
Chassis Control Unit (CCU) Diagnostics
Corner Post Display (CPD) Control Unit Diagnostics
Hitch Control Unit (HCU) Diagnostics
Information Center (ICU) Control Unit Diagnostics
Secondary Hydraulic Control Unit (SCO) Diagnostics
SCV Selective Control Unit (SCU) Diagnostics
Steering System Unit (SSU) Diagnostics
SCV Setup Panel (SUP) Control Unit Diagnostics
Tractor Equipment Control Unit (TEC) Diagnostics
Vehicle Load Center (VLC) Control Unit Diagnostics
Group 50: Power Shift Transmission
Power Shift Transmission Electrical Diagnostics
Tractor Moves During Transmission Calibration
Group 55: Manual Shift Transmission
Hi / Lo Does Not Shift
Manual Shift Transmission Electrical Diagnostics
Manual Shift Transmission Hard to Shift or Grinds Gears
Manual Shift Transmission Jumps Out of Gear
Manual Shift Transmission Loses Oil
Manual Shift Transmission Will Not Hold In Park
Traction Clutch Slips
Vehicle Will Not Move
Group 56: Drive Systems
Axle Electrical Diagnostics
Differential Lock and PTO Problems
Differential Lock Electrical Diagnostics
Differential Lock Will Not Engage / Disengage
One or Both Axles Will Not Transmit Power
PTO Disengages Unexpectedly at Start-Up
PTO Electrical Diagnostics
PTO Engages Aggressively
PTO Slips Under Load
PTO Will Not Stop Turning
Group 60: Steering and Brakes
AutoTrac Electrical Diagnostics
AutoTrac System Accuracy Unacceptable
AutoTrac Continues to Steer Vehicle in One Direction While Disengaged (Loss of Manual Steering)
AutoTrac Loses Engagement or Fails to Engage
Brake Cooling Electrical Diagnostics
Brake Cooling Problem
Intermittent Drag When Turning Steering Wheel
Loss of Power Steering and Brakes
Loss of Steering
Secondary Brake Electrical Diagnostics
Secondary Steering Electrical Diagnostics
Steering is Slow, Sluggish, Hard to Steer, or Stalls Under Load
Steering Wander or Drift
Group 70: Hydraulics
Hydraulic Oil Electrical Diagnostics
Rear Hitch Electrical Diagnostics
SCV Electrical Diagnostics
Hitch Will Not Raise and/or Lower
Hitch Raise/Lower Speed Incorrect
Hitch Cycles Up and Down
Hose Ejects From SCV Coupler
Implement Settles
SCV(s) Does Not Work
Group 90: Operator Station
A/C – Not Cooling Adequately
A/C – Dust In Cab
A/C – Heating Inadequate
A/C – Low or No Airflow From Air Ducts
Active Seat Electrical Diagnostics
Automatic HVAC Electrical Diagnostics
Auxiliary Outlets Electrical Diagnostics
Brake-Signal-Tail-Turn-Warning Light Electrical Diagnostics
Field Flood Light Electrical Diagnostics
Internal Cab Light Electrical Diagnostics
Manual HVAC Electrical Diagnostics
Manual Seat Electrical Diagnostics
Radio / Clock and Speaker Electrical Diagnostics
Remote Mirror Electrical Diagnostics
Right Hand Console Backlighting Electrical Diagnostics
Trailer Lighting Electrical Diagnostics
Vehicle Audible Warning Electrical Diagnostics
Window Wiper Electrical Diagnostics
Section 213: SYSTEM DIAGNOSIS
Group 40: Electrical
Control Unit System Diagnosis
European Lighting System Diagnosis
North American Lighting System Diagnosis
Radar System Diagnosis
Starting and Charging System Diagnosis
Vari-Cool™ Fan Drive System Diagnosis
Group 45: CAN
CAN System Diagnosis
Group 50: Powershift Transmission
PowerShift Transmission System Diagnosis
Group 55: Manual Shift Transmission
Manual Shift Transmission System Diagnosis
Group 56: Drive Systems
Double Reduction Axle Differential Lock System Diagnosis
Double Reduction Axle Lube and Cooling System Diagnosis (Early Design)
Double Reduction Axle Lube and Cooling System Diagnosis (Late Design)
Standard Axle Differential Lock System Diagnosis
Standard Axle System Diagnosis
PTO System Diagnosis
Group 60: Steering and Brakes
Brakes – Brake System Diagnosis
Brakes – Hydraulic Trailer Brake System Diagnosis
Brakes – Secondary Brake System Diagnosis
Steering – AutoTrac System Diagnosis
Steering – Secondary Steering System Diagnosis
Steering – Steering System Diagnosis
Group 70: Hydraulics
Hydraulic System Diagnosis (Standard)
Hydraulic System Diagnosis (High Flow Ag)
Hydraulic System Diagnosis (High Flow Scraper)
SCV – Hitch System Diagnosis
SCV System Diagnosis (High Flow Scraper)
Group 90: Operator Station
A/C – ATC System Diagnosis
A/C – Manual HVAC System Diagnosis
Seat – ActiveSeat™ System Diagnosis
Seat – Heated Seat System Diagnosis
Seat – Manual Seat System Diagnosis
Section 220: ENGINES
Group 05: Engine Performance
Performance Variables
Torque and Power Curve Explanation and Interpretation
Engine Identification
Torque Curve Selection
Engine Protection
Group 10: Engine Cooling System
13.5L Engine Cooling System Theory
13.5L Variable Sheave Fan Drive Component Theory
13.5L Variable Sheave Fan Drive Oil Flow Theory
9.0L Engine Cooling System Theory
9.0L Variable Sheave Fan Drive Component Theory
9.0L Variable Sheave Fan Drive Oil Flow Theory
Group 15: Engine Lubrication System
13.5L Lubrication System Operation
9.0L Lubrication System Operation
Section 230: FUEL AND AIR INTAKE SYSTEMS
Group 05: Engine Fuel System
13.5L Engine Fuel System Theory of Operation
9.0L Engine Fuel System Theory of Operation
Group 10: Engine Air Intake and Exhaust System
13.5L Air and Exhaust System Theory of Operation
9.0L Air and Exhaust System Theory of Operation
Section 240: ELECTRICAL
Group 05: Load Center Fuses, Relays and Ground Points
Load Center Panel—Fuses
Load Center Panel—Relays
Ground Point Locations
Group 10: Operational Checks
Programmable Lighting Operational Check
Group 15: Tests and Adjustments
AutoLoad™ Draft Sensor Zero Shift Test
AutoLoad™ Draft Sensor Adhesive Bond Test
AutoLoad™ Draft Sensor Reed Valve Test
AutoLoad™ Intermittent Draft Signal Test
Group 25: Functional Schematics and Components Reference Lists
Functional Schematics Reference List
Group 30: Connector Information
X009—Battery Power Junction Block (W006, W007, W012, W017, W500, W501, W504)
X010—ServiceAdvisor™ Connector (SE8) (W900)
X010R—Circuit 010 Splice Connector 2 (W500, W501, W504)
X011—ServiceAdvisor™ Interconnect (SE8) (W500, W501, W504, W900)
X050A—Circuit 050 Splice Connector 1 (W500, W501, W504)
X050B—Circuit 050 Splice Connector 2 (W500, W501, W504)
X050C—Circuit 050 Splice Connector 3 (W300, W301, W303)
X050D—Circuit 050 Splice Connector 4 (W300, W301, W303)
X050E Circuit 050 Splice Connector 5 (W573)
X100—Rear Cab Interconnect (W300, W301, W303, W500, W501, W504)
X101—Cab to Steering Column Module Harness Interconnect (SE5) (W110, W500, W501, W504)
X103 Rear Cab Lighting Interconnect (W300, W301, W303, W500, W501, W504)
X104—Chassis to Hood 1 Light Harness Interconnect (W100, W300, W301, W303)
X105—Chassis to Hood 2 Light Harness Interconnect (W100, W300, W301, W303)
X106—Right Fender Light Harness Interconnect (W102, W301) (Eur Only)
X107—Left Fender Light Harness Interconnect (W102, W301) (Eur Only)
X110—Cab-to-Outer-Roof Interconnect (W500, W501, W504, W920)
X111—Cab-to-License Plate Harness Interconnect (W160, W303) (Eur Only)
X132—Left Extremity Light Interconnect (SE6B) (W107, W300, W301) (NA Only)
X133—Right Extremity Light Interconnect (SE6B) (W107, W300, W301) (NA Only)
X134—Left Extremity Light Interconnect (SE6C) (W108, W303) (Eur Only)
X135—Right Extremity Light Interconnect (SE6C) (W108, W303) (Eur Only)
X171—Cab to Beacon Light Harness Interconnect (SE4) (W104, W500, W501, W504)
X171A—Cab to Dual Power Mirror Harness Interconnect (SE4) (W106, W500, W501, W504)
X171B—Dual Power Mirror to Beacon Light Harness Interconnect (SE4) (W104, W106)
X172A—Circuit 172 Splice Connector 1 (W500, W501, W504)
X172B—Circuit 172 Splice Connector 2 (W573)
X173—Beacon Light Harness to Beacon Light Interconnect (SE4) (W104, W105)
X186—Right Hand Console to Panel Back Lighting Interconnect (SE9) (W186, W900)
X187—Manual A/C Switch Backlighting Interconnect (W300, W301, W303)
X210—Cab to A/C Interconnect (SE3) (W210, W220, W500, W501, W504)
X215—Manual HVAC Harness to De-Icing Switch (SE10) (W210, W500, W501, W504)
X220—Cab to ATC Interconnect (SE3) (W220, W500, W501, W504)
X221—Cab to ATC CAN Interconnect (SE3) (W220, W900)
X244—Cab to Right Convenience Outlet Interconnect (SE7) (W005, W014, W900)
X249—Cab to Left Convenience Outlet Interconnect (SE7) (W008, W009, W015)
X301—Cab to RHR Neutral Start Switch Interconnect (SE1) (W500, W501, W570)
X302—Chassis to Engine Injector Harness Interconnect (13.5L) (SE16B) (W301, W303, W401)
X303—Fuel Transfer Pump Harness Interconnect (13.5L) (SE16B) (W301, W303, W402)
X305 Chassis to Front Driveshaft Health Harness Interconnect
X402—Chassis to Engine Injector Harness Interconnect (9L) (SE16A) (W300, W400)
X500—Chassis to PTO Harness Interconnect (W300, W301, W303, W880)
X505—Chassis to Back-Up Alarm Harness Interconnect (SE11A) (W201, W300, W301, W303)
X570—Cab to Main Armrest Control Unit Harness Interconnect (SE13) (W500, W501, W504, W570)
X536—Circuit 536 Splice Connector (W573)
X595—Chassis to Rear Axle Lube Harness Interconnect (W300, W301, W303, W595, W596)
X602—Chassis to Transmission Harness Interconnect (W300, W301, W303, W573, W604)
X614—Circuit 614 Splice Connector (W573)
X700—Cab to Chassis Lighting Interconnect (W300, W301, W303, W500, W501, W504,)
X771—Chassis to SCO Harness Interconnect (W300, W301, W303, W802)
X774—Chassis to Front Brake Cooling Harness Interconnect (W301, W303, W774)
X900—Cab to Driver Information 1 Interconnect (W500, W501,W504, W900)
X901—Cab to Driver Information 2 Interconnect (W500, W501,W504, W900)
X902—Chassis to SSU (AutoTrac™) Harness (SE20) (W300, W301, W303, W700)
X907—Cab to Display Interconnect (SE18) (W500, W501, W504)
X908—Outer Roof to GPS Receiver Interconnect (SE18) (W920)
X910—Business Band / CB Connector (SE7) (W500, W501, W504)
X911A—CAN Tractor Active Terminator Connector (SE8) (W900, W901)
X911B—CAN Tractor Active Terminator Interconnect (SE8) (W900, W901)
X912A—CAN Tractor Passive Terminator Connector (SE8) (W700, W802, W999)
X912B—CAN Tractor Passive Terminator Interconnect (SE8) (W700, W802)
X913—CAN Implement Passive Terminator Connector (SE18) (W920)
X914—CAN Implement Active Terminator Connector (SE18) (W300, W301, W303)
X915A—Cab Implement Connector (2 pin) (SE18) (W500, W501,W504)
X915B—Cab Implement Connector (2 pin) (SE18) (W500, W501,W504)
X916A—Cab Implement Connector (4 pin) (SE18) (W500, W501,W504)
X916B—Cab Implement Connector (4 pin) (SE18) (W500, W501,W504)
X918—Cab to Outer Roof Harness Interconnect (Implement CAN) (SE18) (W500, W501, W504, W920)
X920—Wheel Speed Signal Connector (SE18) (W500, W501, W504)
X920A—Wheel Speed Signal Connector (SE18) (W500, W501, W504)
X920B—Wheel Speed Signal Connector (SE18) (W500, W501, W504)
X922—Cab to ISO Harness Interconnect (SE18) (W500, W501,W504, W922)
X925—JDLink™ Interconnect (SE17) (W901, W902)
X930—Seat to Cab Interconnect (SE2) (W500, W501, W504, W930, W940)
X930A—Cab to Heated Seat Power Harness Interconnect (SE2) (W500, W501, W504, W940, W944)
X930B—Heated Seat Power to Active Seat Upper Harness Interconnect (SE2) (W930, W940, W944)
X940—4- Way Lower Active Seat to Cab Interconnect (SE10B) (W500, W501, W504, W942)
X941—8-Way Upper Active Seat to Cab Interconnect (SE10B) (W500, W501, W504, W940)
X942—6-Way Upper Active Seat to Cab Interconnect (SE10B) (W500, W501, W504, W940)
X943—Heated Seat Control Unit to Switch Harness Interconnect (SE2) (W941, W943)
X944—Heated Seat Power to Control Unit Harness Interconnect (SE2) (W941, W944)
X951—Circuit 951 Splice Connector 6 (W500, W501, W504)
X953—Circuit 953 Splice Connector 5 (W500, W501, W504)
X982—Chassis Harness to Steering Wheel Position Sensor Harness (SE20) (W700, W992)
Group 35: Harness Information
W1—Single Point Ground (W013, W300, W301, W303, W999)
W2—Cab Chassis Ground (W013)
W3—A/C Compressor Clutch Ground (W300, W301, W303)
W5—Cab Floor Ground (W210, W220, W500, W501, W504)
W6—Vehicle Chassis Ground (W021)
W7—Cab Inner Roof Ground (W500, W501, W504)
W8—Radio Ground (W500, W501, W504)
W9—Front Wiper Ground (W920)
W10—Rear Wiper Ground (W920)
W11—Radio Antenna Ground
W12—Battery Ground (W011, W020)
W13—Right Under Cab Single Point Ground (W300, W301, W303)
W14—Left Under Cab Single Point Ground (W300, W301, W303)
W15—Engine Ground (W021)
W16—Starter Ground (W021)
W005—Right Convenience Outlet Harness (NA only)
W006—VLC Power Cable
W007—CLC Power Cable
W008—Left Convenience Outlet Harness (NA only)
W009—Left Convenience Outlet Harness (Eur only)
W010—Positive Battery Cable
W011—Negative Battery Cable
W012—Cab Power Cable (13.5L)
W013—Cab Ground Cable
W014—Right Convenience Outlet Harness (Eur only)
W015—Field Office Harness
W016—Auxiliary Power Strip
W017—Cab Power Cable (9.0L)
W019—Positive Battery Cable (3 Battery)
W020—Negative Battery Cable (3 Battery)
W021—Starter/Engine Ground Cable
W100—Hood Lights Harness
W102—Tail Light Harness (Eur Only)
W104—Beacon Light Harness
W105—Beacon Light Extension Harness
W106—Dual Power Mirror Harness
W107—Extremity Light Harness (NA Only)
W108—Extremity Light Harness (Eur only)
W110—Steering Column Module Harness
W160—License Plate Light Harness (Eur Only)
W186—Panel Backlighting Inverter Harness
W201—Back-Up Alarm Harness
W210—Manual HVAC Harness
W220—ATC HVAC Harness
W300—9L Wheel Chassis Harness (NA Only)
W301—13.5L Wheel Chassis Harness (NA Only)
W303—13.5L Wheel Chassis Harness (Eur Only)
W309—13.5L Wheel Chassis Harness (Scraper Only 10000-) (NA Only)
W400—Engine Fuel Injector Harness
W401—13.5L Engine Fuel Injector Harness
W402—Fuel Transfer Pump Harness
W500—PST Cab Harness (NA Only)
W501—PST Cab harness (Eur Only)
W504—MST Cab harness (NA Only)
W570—Main Armrest Control Unit Harness (14 Pin)
W571—Standard Armrest Control Unit Harness (20 Pin)
W572—Armrest SCV 5 and Front Hitch Harness (22 Pin)
W573—PST Transmission Harness
W574—Single Lever Control Assembly Harness (18 Pin)
W576— Armrest Control Unit Harness (22 Pin) (PST Only)
W595—Rear Axle Lube Harness
W596—Rear Brake Cooling Harness
W604—Transmission Intermediate Harness (MST Only)
W700—SSU Harness (AutoTrac™)
W774—Front Brake Cooling Harness
W790—AutoLoad™ Interconnect Harness
W791—TouchSet™ Depth Control Interconnect Harness
W802—SCO Harness
W873—SCV IV (SCV V Option) Solenoid Harness
W874—SCV II/SCV III Solenoid Harness
W875—Hitch/SCV I Solenoid Harness
W877—High Flow Scraper SCV Harness
W878—SCV VI Solenoid Harness
W879—High Flow Scraper SCV Harness (Scraper Only 10000-)
W880—PTO Harness
W900—Right Hand Console Harness
W901—JDLink™ Cab Harness
W902—JDLink™ Control Unit Harness
W920—Outer Roof Harness
W922—ISO Cornerpost Harness
W930—Air Seat Harness
W940—Active Seat Upper Harness
W941—Heated Seat Control Unit Harness
W942—Active Seat Lower Harness
W943—Heated Seat Switch Harness
W944—Heated Seat Power Harness
W992—Steering Wheel Position Sensor Harness (AutoTrac™)
W999 Front Driveshaft Health Harness
Group SE01: SE01 — Power Supply, Starting and Charging
Power Supply, Starting and Charging Reference List
Power Supply, Starting and Charging Schematic and Circuit Drawing
Battery Inspection Test
Charging System Circuit Test
Starting System Circuit Test
F001—Master Fuse (SE1) (W010, W012, W017, W018, W019)
G001—Battery (SE1) (W010, W011, W019, W020)
G002—Battery (SE1) (W010, W011, W019, W020)
G003—Battery (SE1) (W019, W020)
G301—Alternator (SE1) (W300, W301, W303, W999)
K301—Starter Relay (SE1) (W300, W301, W303)
M301—Starter Motor (SE1) (W010, W019, W300, W301, W303)
S001—Key Switch (SE1) (W500, W501, W504)
S300—Start Aid Switch (SE1) (W300, W301, W303)
S301—Neutral Start Switch (SE1) (W570) (PST)
S302—Neutral Start Switch (SE1) (W604) (MST)
V1—Alternator Diode (SE1) (W300, W301, W303)
Y300—Ether Solenoid (SE1) (W300, W301, W303)
Group SE02: SE02 — Manual Seat
Standard Seat Reference List
Standard Seat Schematic and Circuit Diagram
Standard Seat Height Control Switch Circuit Test
Standard Seat Compressor Assembly Circuit Test
Standard Seat Diode Circuit Test
Heated Seat Supply Voltage and Ground Circuit Test
Heated Seat Switch Circuit Test
Heated Seat Heating Element Circuit Test
A942—Heated Seat Control Unit (SE2) (W941)
E946—Heated Seat Elements (SE2) (W941)
E947—Backrest Heating Element (SE2) (W941)
M092—Air Seat Compressor Motor (SE2) (W930)
S930—Operator Presence Switch (SE2, SE10B) (W930, W940)
S931—Standard Seat Height Control Switch (SE2) (W930)
S943—Heated Seat Switch (SE10B) (W943)
V3—Standard Seat Diode (SE2) (W930)
Group SE03: SE03 — Manual A/C and Automatic Temperature Control (ATC)
Manual AC and Automatic Temperature Control Unit (ATC) Reference List
Manual AC and Automatic Temperature Control Unit (ATC) Schematic and Circuit Diagram
ATC-Automatic Temperature Control Unit System Power and Ground Circuit Test
ATC-Air Flow Mode Motor Circuit Test
ATC-Ambient Temperature Sensor Circuit Test
ATC-Blower Motor Driver Circuit Test
ATC-Cab Temperature Sensor Circuit Test
ATC-Circulation Blower Motor Circuit Test
ATC-Evaporator Temperature Sensor Circuit Test
ATC-Outlet Air Temperature Sensor Circuit Test
ATC-Pressurizer Blower Motor Circuit Test
ATC-Refrigerant Pressure Sensor Circuit Test
ATC-Water Valve Motor Circuit Test
Manual-HVAC Circulation Blower Motor Circuit Test
Manual-HVAC Pressurizer Blower Motor Circuit Test
A220—Automatic Temperature Control Unit (ATC) (SE3)
A220X1—ATC Connector (SE3) (W220)
A221—Blower Motor Driver (SE3) (W220)
B220—Cab Temperature Sensor (SE3) (W220)
B221—Evaporator Temperature Sensor (SE3) (W220)
B222—Ambient Temperature Sensor (SE3) (W920)
B223—Outlet Air Temperature Sensor (SE3) (W220)
B224—Refrigerant Pressure Sensor (SE3) (W220)
KA1—Manual HVAC Circulation Blower Motor Relay (SE3) (W210)
M210—Manual HVAC Circulation Blower Motor (SE3) (W210)
M211—Pressurizer Blower Motor (SE3) (W500, W501, W504)
M220—ATC Circulation Blower Motor (SE3) (W220)
R210—Blower Motor Resistor (SE3) (W210)
S210—Blower Motor Switch (SE3) (W210)
Y220—Air Flow Mode Motor (SE3) (W500, W501, W504)
Y221—Water Valve Motor (SE3) (W220)
Group SE04: SE04 — Remote Mirror Option
Remote Mirror Option Reference List
Remote Mirror Option—Beacon Light Schematic and Circuit Diagram
Remote Mirror Adjustment Circuit Test
Beacon Light Circuit Test
E105—Beacon Light (SE4) (W105)
H110—Roof Beacon Indicator (SE4) (W104)
M950—Right Mirror Adjustment Motor (SE4) (W106)
M951—Left Mirror Adjustment Motor (SE4) (W106)
S106—Rotary Beacon Light Switch (SE4) (W104)
S951—Mirror Adjustment Switch (SE4) (W106)
Group SE05: SE05 — Radio, Dome Lamp and Steering Column Module
Radio, Dome Lamp and Multi-Function Switch Reference List
Radio, Dome Lamp and Multi-Function Switch Schematic and Circuit Diagram
Steering Column Module Circuit Test
Steering Column Module-Turn Signal Switch Circuit Test
Steering Column Module-High / Low Beam Light Switch Circuit Test
Steering Column Module-Horn Switch Circuit Test
Dome Lamp Circuit Test
Dome Lamp Switch Circuit Test
Left Hand Door Switch Circuit Test
Radio / Clock Circuit Test
Radio Speakers Circuit Test
Right Hand (RH) Console Lamp Test
A100—Steering Column Indicator Lights (SE5) (W110)
A101—Steering Column Turn/Horn/HiLo Switches (SE5) (W110)
A240—Radio / Clock (SE5) (W500, W501, W504)
B240—Right Front Speaker (SE5) (W920)
B241—Left Front Speaker (SE5) (W920)
B242—Right Rear Speaker (SE5) (W920)
B243—Left Rear Speaker (SE5) (W920)
C240—Radio Antenna (SE5)
E100—Dome Lamp (SE5) (W500, W501, W504)
E101—RH Console Lamp (SE5) (W500, W501, W504)
E102—Left Entry Light (SE5) (W920)
H100—Right Turn Indicator (SE5) (W110)
H101—Left Turn Indicator (SE5) (W110)
H102—Hazard Lights Indicator (SE5) (W110)
H103—Tractor Indicator (SE5) (W110)
H104—Trailer 1 Indicator (SE5) (W110)
H105—Trailer 2 Indicator (SE5) (W110)
H107—High Beam Indicator (SE5) (W110)
S104—Dome Lamp Switch (SE5) (W500, W501, W504)
S105—LH Door Switch (SE5) (W500, W501, W504)
Group SE06: SE06 — CLC/TEC – Implement Gateway Control Unit Functions
CLC/TEC – Implement Gateway Control Unit Reference List
CLC/TEC – Implement Gateway Control Unit Schematic and Diagram (SE6)
A922—Implement Gateway Control Unit (CLC, TEC) (SE6) (W500, W501, W504)
A922-1—Cab Load Center Control Unit (CLC) (SE6A) (W500, W501, W504)
A922-2—Tractor Equipment Control Unit (TEC) (SE6A) (W500, W501, W504)
A922-3—CLC-North American Lighting/Trailer (SE6B) (W500, W504)
A922-4—CLC-European Lighting/Trailer (SE6C) (W501)
A922X1—CLC, TEC Connector (SE6) (W500, W501, W504)
A922X2—CLC, TEC Connector (SE6) (W500, W501, W504)
A922X3—CLC, TEC Connector (SE6) (W500,W501,W504)
A922X4— CLC, TEC Connector (SE6) (W007)
E103—Right Fender Turn Signal Light (SE6B) (W300, W301)
E104—Left Fender Turn Signal Light (SE6B) (W300, W301)
E130—Right Tail/Brake Light (SE6B) (W300, W301) (NA Only)
E131—Left Tail/Brake Light (SE6B) (W300, W301) (NA Only)
E132—Left Front Roof Warning Light (SE6B) (W920) (NA Only)
E133—Right Rear Roof Warning Light (SE6B) (W920) (NA Only)
E134—Left Rear Roof Warning Light (SE6B) (W920) (NA Only)
E135—Right Front Roof Warning Light (SE6B) (W920) (NA Only)
E136—Left Extremity Transport Light (SE6B, SE6C) (W107, W108)
E137—Right Extremity Transport Light (SE6B, SE6C) (W107, W108)
E160—Right Front Clearance/Warning Light (SE6C) (W303) (Eur Only)
E161—Left Front Clearance/Warning Light (SE6C) (W303) (Eur Only)
E164—Rear License Plate Light (SE6C) (W160) (Eur Only)
E165—Right Tail/Brake Light (SE6C) (W303) (Eur Only)
E166—Left Tail/Brake Light (SE6C) (W303) (Eur Only)
E167—Left Rear Fender Warning Light (SE6C) (W303) (Eur Only)
E168—Right Rear Fender Warning Light (SE6C) (W303) (Eur Only)
E180—Left Rear-Facing Side Roof Flood Light (SE6A) (W920)
E181—Left Front-Facing Side Roof Flood Light (SE6A) (W920)
E183—Left Rear Fender Inner Flood Light (SE6A) (W300, W301, W303)
E184—Right Rear-Facing Side Roof Flood Light (SE6A) (W920)
E186—Right Rear Fender Inner Flood Light (SE6A) (W300, W301, W303)
E187—Right Front-Facing Side Roof Flood Light (SE6A) (W920)
E188—Left Rear Fender Outer Flood Light (SE6A) (W300, W301, W303)
E189—Right Rear Fender Outer Flood Light (SE6A) (W300, W301, W303)
KTF—Trailer Flood Light Relay (SE6A) (W500, W501, W504)
M240—Front Wiper Motor (SE6A) (W920)
M241—Rear Wiper Motor (SE6A) (W920)
S100—Road Light Switch (SE6A) (W900)
S101—Hazard Light Switch (SE6A) (W900)
S121—Field Light Switch (SE6A) (W900) (Eur Only)
S241—Front Wiper Switch (SE6A) (W900)
S242—Rear Wiper Switch (SE6A) (W900)
X130—Trailer Lighting and Accessory Connector (SE6B) (W300, W301) (NA Only)
X160—Trailer Lighting and Accessory Connector (SE6C) (W303) (Eur Only)
X161—Trailer Flood Light Connector (SE6C) (W303) (Eur Only)
Group SE06A: SE06A — CLC/TEC – Cab Load Center Control Unit and Tractor Equipment Control Unit Functions
CLC/TEC – Cab Load Center and Tractor Equipment Control Schematic and Diagram (SE6A)
CLC – Cab Load Center Control Unit ELX Output 1 Circuit Test
CLC – Cab Load Center Control Unit ELX Wake-Up Output Circuit Test
CLC – Cab Load Center Control Unit System Power and Ground Circuit Test
CLC – Field Light Switch Circuit Test
CLC – Front-Facing Side Roof Flood Light Circuit Test
CLC – Front Wiper Motor Circuit Test
CLC – Front Wiper Switch Circuit Test
CLC – Hazard Light Switch Circuit Test
CLC – Rear-Facing Side Roof Flood Light Circuit Test
CLC – Rear Fender Inner Flood Light Circuit Test
CLC – Rear Fender Outer Flood Light Circuit Test
CLC – Rear Wiper Motor Circuit Test
CLC – Rear Wiper Switch Circuit Test
CLC – Right Hand Console Switch Backlighting Circuit Test
CLC – Road Light Switch Circuit Test
TEC – Tractor Equipment Control Unit Power Relay Output Circuit Test
TEC – Tractor Equipment Control Unit System Voltage and Ground Circuit Test
Group SE06B: SE06B — CLC – North American Lighting Functions
CLC – North American Lighting/Trailer Schematic and Diagram (SE6B)
CLC – Brake Light Circuit Test (NA Only)
CLC – Left Extremity Light Circuit Test (NA Only)
CLC – Left Fender Turn Signal Light Circuit Test (NA Only)
CLC – Left Roof Warning Light Circuit Test (NA Only)
CLC – Left Tail Light Circuit Test (NA Only)
CLC – Right Extremity Light Circuit Test (NA Only)
CLC – Right Fender Turn Signal Circuit Test (NA Only)
CLC – Right Roof Warning Light Circuit Test (NA Only)
CLC – Right Tail Light Circuit Test (NA Only)
CLC – Trailer Flood Light Circuit Test (NA Only)
CLC – Trailer Lighting / Accessory Circuit Test (NA Only)
Group SE06C: SE06C — CLC – European Lighting Functions
CLC – European Lighting/Trailer Schematic and Diagram (SE6C)
CLC – Brake Light Circuit Test (Eur Only)
CLC – Left Extremity Light Circuit Test (Eur Only)
CLC – Left Extremity Clearance Light Circuit Test (Eur Only)
CLC – Left Front Clearance Light Circuit Test (Eur Only)
CLC – Left Front Warning Light Circuit Test (Eur Only)
CLC – Left Rear Fender Turn Signal Light Circuit Test (Eur Only)
CLC – Left Tail Light Circuit Test (Eur Only)
CLC – Rear License Plate Light Circuit Test (Eur Only)
CLC – Right Extremity Light Circuit Test (Eur Only)
CLC – Right Extremity Clearance Light Circuit Test (Eur Only)
CLC – Right Front Clearance Light Circuit Test (Eur Only)
CLC – Right Front Warning Light Circuit Test (Eur Only)
CLC – Right Rear Fender Turn Signal Light Circuit Test (Eur Only)
CLC – Right Tail Light Circuit Test (Eur Only)
CLC – Trailer Flood Light Circuit Test (Eur Only)
CLC – Trailer Lighting and Accessory Connector Circuit Test (Eur Only)
Group SE07: SE07 — Accessory Connectors
Accessory Connectors Reference List
Accessory Connectors Schematic and Circuit Diagram
Left Junction Block Circuit Test
Right Junction Block Circuit Test
Auxiliary Power Strip Circuit Test
Lighter Circuit Test
Convenience Outlet #1 Circuit Test
Convenience Outlet #2 Circuit Test
Business Band/CB Radio Prewire Test
X240—Left Junction Block (SE7) (W015, W500, W501, W504)
X241—Right Junction Block (SE7) (W016, W500, W501, W504, W901)
X242—Convenience Outlet #1 (SE7) (W005) (NA Only)
X243—Convenience Outlet #2 (SE7) (W008) (NA Only)
X245—Lighter #1 (SE7) (W900)
X246—Lighter #2 (SE7) (W015)
X247—Lighter #3 (SE7) (W015)
X248—Auxiliary Power Strip (SE7) (W016)
X250—Convenience Outlet #2 (SE7) (W009) (Eur Only)
X251—Convenience Outlet #1 (SE7) (W014) (Eur Only)
X910—Business Band / CB Connector (SE7) (W500, W501, W504)
Group SE08: SE08 — Controller Area Network (CAN) Termination
CAN Termination Reference List
CAN Communication System Schematic and Circuit Diagrams
CAN Communication System Diagnostic Wiring Diagrams
CAN System Diagnostic Wiring Diagram – Cab Harnesses
CAN System Diagnostic Wiring Diagram – Engine and Chassis Harnesses
CAN Circuit Interconnections and Splice Locations
CAN Communication Fault Checks
CAN Communication System Theory Of Operation
CAN Network Voltage Checks
A911—CAN Tractor Active Terminator (SE8) (W900)
A912—CAN Tractor Passive Terminator (SE8) (W999)
Group SE09: SE09 — CPD – Corner Post Display, ICU – Information Display, and SUP – SCV Setup Panel Display
CPD – Corner Post Display, ICU – Information Display, and SUP – SCV Setup Panel Display Reference List
CPD – Corner Post Display, ICU – Information Display, and SUP – SCV Setup Panel Display Schematic and Circuit Diagram
ICU-Information Display System Power and Ground Circuit Test
Right Hand Console Inverter And Panel Backlighting Circuit Test
SUP-Setup Panel Control Unit Power and Ground Circuit Test
A186—Inverter Backlighting (SE9) (W500, W501, W504, W900)
A901—Information Center Control Unit (ICU) (CommandCenter™) (SE9)
A901X1—ICU Connector (SE9) (W900)
A902—SCV Setup Panel Control Unit (SUP) (SE9)
A902X1—SUP Connector (SE9) (W900)
A903—Corner Post Display (SE9) (W500, W501, W504)
E191—Manual A/C Temperature and Blower Switch Backlighting Panel (SE9) (W186)
E192—Road Light & Front Wiper Switch Backlighting Panel (SE9) (W186)
H200—Warning Horn (SE9) (W900)
Group SE10: SE10 — CAB/ASU – Cab Control Unit Functions
CAB/ASU – Cab Control Unit Reference List
CAB/ASU – Cab Control Unit Schematic and Diagram (SE10)
A110—Cab Control Unit (CAB, ASU) (SE10) (W500, W501, W504)
A110-1—CAB Control Unit (SE10A) (W500, W501, W504)
A110-5—Active Seat Control Unit (ASU) (SE10B) (W500, W501, W504)
A110X1—CAB, ASU Connector (SE10) (W500, W501, W504)
A110X2—CAB, ASU Connector (SE10) (W500, W501, W504)
A110X3—CAB, ASU Connector (SE10) (W500, W501, W504)
A940—Active Seat Compressor Assembly (SE10B) (W940)
B513—Clutch Pedal Position Sensor (SE10A) (W500, W501, W504)
B715—Secondary Brake Sensor/Switch (SE10A) (W900) (Eur Only)
B940—Seat Accelerometer Sensor (SE10B) (W940)
B941—Seat Position Sensor (SE10B) (W940)
K940—Active Seat Compressor Relay (SE10B) (W940)
S211—A/C On / Off Switch (SE10A) (W210)
S212—A/C De-icing Switch (SE10A) (W210)
S213—A/C Dual Pressure Switch (SE10A) (W210)
S215—A/C De-icing Switch (SE10A) (W210)
S240—Implement Switch (SE10A) (W300, W301, W303)
S503—Differential Lock Switch (SE10A) (W500, W501, W504)
S505—Brake Switch (SE10) (W500, W501, W504)
S592—Deceleration Switch (SE10) (W500, W501, W504)
S930—Operator Presence Switch (SE2, SE10B) (W930,W940)
S941—Active Seat Height Control Switch (SE10B) (W940)
S942—Active Seat Firmness Control Switch (SE10B) (W940)
Y941—Active Seat Raise / Lower Solenoid (SE10B) (W942)
Y942—Active Seat Flow Control Solenoid (SE10B) (W942)
Group SE10A: SE10A — CAB – CAB Control Unit Functions
CAB – CAB Control Unit Schematic and Circuit Diagram
CAB – CAB Control Unit Sensor Supply Voltage Circuit Test
CAB – CAB Control Unit System Power and Ground Circuit Test
CAB – A/C Switch Circuit Test
CAB – Brake Pedal Switch Circuit Test
CAB – Clutch Pedal Position Sensor Circuit Test
CAB – Deceleration Switch Circuit Test
CAB – Differential Lock Switch Circuit Test
CAB – Implement Switch Circuit Test
CAB – Operator Presence Switch Circuit Test
CAB – Secondary Brake Sensor and Switch Circuit Test
Group SE10B: SE10B — ASU – Active Seat Control Unit Functions
ASU – Active Seat Control Unit Schematic and Circuit Diagram
ASU – Active Seat Control Unit Supply Voltage and Ground Circuit Test
ASU-Pressure Reducing Valve Solenoid Circuit Test
ASU-Raise / Lower Valve Solenoid Circuit Test
ASU-Bleed (Vent) Valve Solenoid Circuit Test
ASU-Accelerometer Sensor Circuit Test
ASU-Position Sensor Circuit Test
ASU-Firmness Adjustment Switch Circuit Test
ASU-Height Control Switch Circuit Test
ASU-Air Compressor Assembly Circuit Test
Group SE11: SE11 — VLC/CCU – Vehicle Control Unit Functions
VLC/CCU – Vehicle Control Unit Reference List
VLC/CCU – Vehicle Control Unit (CCU and VLC) Schematic and Diagram (SE11)
A210—A/C Compressor Clutch (SE11B) (W300, W301, W303)
A570—Vehicle Control Unit (SE11) (CCU, VLC)
A570-1—Chassis Control Unit (CCU) (SE11A) (W300, W301, W303)
A570-2—Vehicle Load Center Control Unit (VLC) (SE11B) (W300, W301, W303)
A570X1—VLC, CCU Connector (SE11) (W300, W301, W303)
A570X2—VLC, CCU Connector (SE11) (W300, W301, W303)
A570X3—VLC, CCU Connector (SE11) (W300, W301, W303)
A570X4—VLC, CCU Connector (SE11) (W300, W301, W303)
B303—Fuel Level Sensor (SE11A) (W300, W301, W303)
B307—Air Filter Restriction Sensor (SE11A) (W300, W301, W303)
B501— Rear PTO Speed Sensor (SE11A) (W880)
B502—Primary Wheel Speed Sensor (SE11A) (W604) (MST only)
B526—Diagnostic Pressure Sensor (SE11A) (W300, W301, W303)
B573—Rear PTO Oil Temperature Sensor (SE11A) (W880)
B592—IMS Reverse Detect Sensor (SE11A) (W604) (MST Only)
B594—Transmission Oil Pressure Sensor (SE11) (W604) (MST only)
B595—Axle Lube Oil Pressure Sensor (SE11) (W595)
B596—Double Reduction Axle Lube Pressure Sensor (SE11) (W301, W303, W596)
B597—Double Reduction Front Axle Lube Pressure Sensor (SE11) (W301, W303, W774)
B700—Hydraulic Oil Temperature Sensor (SE11A) (W300, W301, W303)
B711—Hydraulic Oil Level Sensor (SE11) (W300, W301, W303)
B790—Transmission Oil Filter Sensor (SE11) (W604) (MST Only)
B920—Horn (SE11A) (W100)
E140—Left Hi/Lo Headlight (SE11B) (W100) (NA Only)
E141—Right Hi/Lo Headlight (SE11B) (W100) (NA Only)
E142—Left Outer Hood Flood Light (SE11B) (W100)
E143—Right Outer Hood Flood Light (SE11B) (W100)
E146—Left Outer Hood HID Light (SE11B) (W100)
E149—Right Outer Hood HID Light (SE11B) (W100)
E152—Center Spot Light (SE11B) (W100)
E155—Left Front Inner Flood Light (SE11) (W100) (Eur Only)
E156—Right Front Inner Flood Light (SE11) (W100) (Eur Only)
E157—Left Hi/Lo Headlight (SE11) (W303) (Eur Only)
E158—Right Hi/Lo Headlight (SE11) (W303) (Eur Only)
H201—Backup Alarm (SE11A) (W201)
K990—Secondary Steering Relay (SE11) (W303) (Eur Only)
M242—Rear Washer Pump (SE11B) (W300, W301, W303)
M243—Front Washer Pump (SE11B) (W300, W301, W303)
M990—Secondary Steering Motor (SE11) (W303) (Eur Only)
S710—Hydraulic Pump Filter Restriction Switch (SE11A) (W300, W301, W303)
S990—Secondary Steering Pressure Switch (SE11) (W303) (Eur Only)
V2—A/C Compressor Clutch Diode (SE11B) (W300, W301, W303)
Y500—Rear PTO Solenoid (SE11) (W880)
Y502—Rear Differential Lock Solenoid (SE11) (W300, W301, W303, W596)
Y503—Front Differential Lock Solenoid (SE11) (W774)
Y590—MST HI/LO Solenoid (SE11) (W604) (MST Only)
Y621—Double Reduction Axle Lube Solenoid (SE11) (W573)
Y622—Double Reduction Front Axle Lube Solenoid (SE11) (W774)
Y623—Double Reduction Rear Axle Lube Solenoid (SE11) (W596)
Group SE11A: SE11A — CCU – Chassis Control Unit Functions
CCU – Chassis Control Unit (CCU) Schematic and Diagram (SE11A)
CCU – Chassis Control Unit System Power and Ground Circuit Test
CCU – Chassis Control Unit Sensor Supply Voltage Circuit Test
CCU – Air Filter Restriction Sensor Circuit Test
CCU – Axle Lube Oil Pressure Sensor Circuit Test
CCU – Backup Alarm Circuit Test
CCU – Diagnostic Pressure Sensor Circuit Test
CCU – Double Reduction Axle Lube Pressure Sensor Circuit Test
CCU – Double Reduction Front Axle Lube Pressure Sensor Circuit Test
CCU – Double Reduction Axle Lube Solenoid Circuit Test
CCU – Double Reduction Front Axle Lube Solenoid Circuit Test
CCU – Front Differential Lock Solenoid Circuit Test
CCU – Fuel Level Sensor Circuit Test
CCU – Hydraulic Oil Level Sensor Circuit Test
CCU – Hydraulic Oil Temperature Sensor Circuit Test
CCU – Hydraulic Pump Filter Restriction Switch Circuit Test
CCU – IMS Reverse Detect Sensor Circuit Test
CCU – MST HI/LO Solenoid Circuit Test
CCU – Primary Wheel Speed Sensor Circuit Test
CCU – Radar Sensor Circuit Test
CCU – Rear Differential Lock Solenoid Circuit Test
CCU – Rear PTO Oil Temperature Sensor Circuit Test
CCU – Rear PTO Solenoid Circuit Test
CCU – Rear PTO Speed Sensor Circuit Test
CCU – Secondary Steering Motor Circuit Test
CCU – Secondary Steering Pressure Switch Circuit Test
CCU – Transmission Oil Filter Restriction Switch Circuit Test
CCU – Transmission Oil Pressure Sensor Circuit Test
Group SE11B: SE11B — VLC – Vehicle Load Center Control Unit Functions
VLC – Vehicle Load Center (CLC) Control Unit Schematic and Diagram (SE11B)
VLC – Vehicle Load Center Control Unit System Power and Ground Circuit Test
VLC – Air Conditioner Compressor Clutch Circuit Test
VLC – Center Spot Light Circuit Test
VLC – Vehicle Load Center Control Unit ELX Output 2 Circuit Test
VLC – Front Washer Pump Circuit Test
VLC – Rear Washer Pump Circuit Test
VLC – Horn Circuit Test
VLC – Left Front Inner Flood Light Circuit Test
VLC – Right Front Inner Flood Light Circuit Test
VLC – Left Front Outer Flood Light Circuit Test
VLC – Right Front Outer Flood Light Circuit Test
VLC – Left High/Low Beam Head Lights Circuit Test
VLC – Right High/Low Beam Head Lights Circuit Test
Group SE12: SE12 — PTP – Powershift Transmission Control Unit Functions
PTP – Power Train Power Shift Control Unit Reference List
PTP – Power Train Power Shift Control Unit Schematic and Circuit Diagram
PTP – Power Train Power Shift Control Unit System Power and Ground Circuit Test
A610—Power Train Power Shift Control Unit (PTP) (SE12)
A610X1—PTP Connector (SE12) (W573)
A610X2—PTP Connector (SE12) (W573)
A610X3—PTP Connector (SE12) (W573)
A610X4—PTP Connector (SE12) (W573)
B593—Axle Filter Pressure Switch (SE12) (W573) (PST only)
B610—Transmission Oil Pressure Sensor (SE12) (W573) (PST Only)
B611—Park Pressure Sensor (SE12) (W573)
B612—Transmission Output Speed #2 Sensor (SE12) (W573)
B613—Transmission Output Speed #1 Sensor (SE12) (W573)
B614—Transmission Input Speed Sensor (SE12) (W573)
B615—Transmission Cylinder Speed Sensor (SE12) (W573)
B616—Transmission 5th Speed Sensor (SE12) (W573)
B617—Transmission Oil Temperature Sensor (SE12) (W573)
KT1—Transmission Enable Relay (SE12) (PST Only) (W500, W501)
S709—Transmission Filter Switch (SE12) (W573)
Y610—M Solenoid (SE12) (W573)
Y611—1 Solenoid (SE12) (W573)
Y612—B Solenoid (SE12) (W573)
Y613—R Solenoid (SE12) (W573)
Y614—A Solenoid (SE12) (W573)
Y615—C Solenoid (SE12) (W573)
Y616—L Solenoid (SE12) (W573)
Y617—H Solenoid (SE12) (W573)
Y618—2 Solenoid (SE12) (W573)
Y619—Park Solenoid #1 (SE12) (W573)
Y620—Park Solenoid #2 (SE12) (W573)
Group SE13: SE13 — ACU – Armrest Control Unit Functions
ACU – Armrest Control Unit Reference List
ACU – Armrest Control Unit Schematic and Circuit Diagram
ACU – Armrest Control Unit System Power and Ground Circuit Test
ACU – Armrest Control Unit Sensor Power 1 Circuit Test
ACU – Armrest Control Unit Sensor Power 2 Circuit Test
ACU – Auxiliary Switches Circuit Test
ACU – Fore/Aft Single Lever Control Sensor Circuit Test
ACU – Hand Throttle Position Sensor Circuit Test
ACU – IMS Sequence Switch Circuit Test
ACU – Left/Right Single Lever Control Sensor Circuit Test
ACU – MST Hi/Lo Shift Module Circuit Test
ACU – Operator Hand Presence Switch Circuit Test
ACU – Neutral/Park Circuit Test
ACU – Rear Hitch Control Lever Sensor Circuit Test
ACU – Rear PTO Switch Circuit Test
ACU – Resume Switch Circuit Test
ACU – Right Hand Reverser Switch Assembly Circuit Test
ACU – SCV I Control Lever Sensor Circuit Test
ACU – SCV II Control Lever Sensor Circuit Test
ACU – SCV III Control Lever Sensor Circuit Test
ACU – SCV IV Control Lever Sensor Circuit Test
ACU – SCV V Control Lever Sensor Circuit Test
ACU – SCV VI Control Lever Sensor Circuit Test
ACU – Transmission Enable Circuit Test
ACU – Transport Lock Switch Circuit Test
A573—Right Hand Reverser (SE13) (W576)
A575—Hand Throttle Position Sensor (SE13) (W571)
A576—MST Hi/Lo Shift Module (SE13) (W576)
A773—Single Lever Control Assembly (SE13) (W574)
A923—Armrest Control Unit (ACU) (SE13)
A923X1—ACU Connector (14 Pin) (SE13) (W570)
A923X2—ACU Connector (20 Pin) (SE13) (W571)
A923X3—ACU Connector (22 Pin) (SE13) (W576)
A923X4—ACU Connector (18 Pin) (SE13) (W574)
A923X5—ACU Connector (12 Pin) (SE13) (W572)
R700—SCV I Control Lever Sensor (SE13) (W571)
R701—SCV II Control Lever Sensor (SE13) (W571)
R702—SCV III Control Lever Sensor (SE13) (W571)
R703—SCV IV Control Lever Sensor (SE13) (W571)
R704—SCV V Control Lever Sensor (SE13) (W572)
R705—SCV VI Control Lever Sensor (SE13) (W572)
R800—Rear Hitch Control Lever Sensor (SE13) (W571)
S501—Rear PTO Switch (SE13) (W571)
S509—IMS Sequence Switch (SE13) (W571)
S514—Auto Resume Switch (SE13) (W576)
S515—Transport Lock Switch (SE13) (W574)
Group SE14: SE14 — SCU/HCU/BRC – Deluxe Hydraulic Controller Function
SCU/HCU/BRC – Deluxe Hydraulic Controller Reference List
SCU/HCU/BRC – Deluxe Hydraulic Controller Schematic and Circuit Diagram
A770—Deluxe Hydraulic Control Unit (HCU, SCU, BRC) (SE14)
A770-1—Hitch Control Unit (HCU) (SE14A)
A770-2—Deluxe Hydraulic Control Unit (SCU) (SE14B)
A770-4—Brake Control Unit (BRC) (SE14D)
A770X1—HCU, SCU, BRC CONNECTOR (SE14) (W300, W301, W303)
A770X2—HCU, SCU, BRC Connector (SE14) (W300, W301, W303)
A770X3—HCU, SCU, BRC Connector (SE14) (W300, W301, W303)
B706—Secondary Brake Pressure Sensor (SE14D) (Eur Only) (W303)
B870—Rear Hitch Position Sensor (SE14A) (W300, W301, W303)
B871—Rear Hitch Draft Sensor (SE14A) (W300, W301, W303)
B890—Implement Draft Sensor (AUTOLOAD™ only) (SE14) (W790)
S830—Rear Hitch External Switch (SE14A) (W300, W301, W303)
X270—Option Configuration Connector (SE14B) (W300, W301, W303, W790)
X271—AUTOLOAD™ 9 Pin Option Connector (SE14B) (W790)
X272—TouchSet™ Depth Control 9 Pin Option Connector (SE14B) (W791)
X808—Chassis Harness to SCV II and SCV III (SE14B) (W300, W301, W303, W874, W877)
X809—Chassis Harness to Hitch and SCV I (SE14A, SE14B) (W300, W301, W303, W875, W877)
X810—Chassis Harness to SCV IV (SCV V Option) (SE14B, SE15) (W300, W301, W303, W873, W877)
Y701—Secondary Brake Valve (SE14D) (Eur Only) (W303)
Y774—Front Brake Cooling Solenoid (SE14D) (W774)
Y775—Rear Brake Cooling Solenoid (SE14D) (W596)
Y830—Rear Hitch Raise Solenoid (SE14A) (W875)
Y831—Rear Hitch Lower Solenoid (SE14A) (W875)
Y832—SCV I Extend Solenoid (SE14B) (W875) (W877)
Y833—SCV I Retract Solenoid (SE14B) (W875) (W877)
Y834—SCV II Extend Solenoid (SE14B) (W874) (W877)
Y835—SCV II Retract Solenoid (SE14B) (W874) (W877)
Y836—SCV III Extend Solenoid (SE14B) (W874) (W877)
Y837—SCV III Retract Solenoid (SE14B) (W874) (W877)
Y838—SCV IV Extend Solenoid (SE14B) (W873) (W877)
Y839—SCV IV Retract Solenoid (SE14B) (W873) (W877)
Group SE14A: SE14A — HCU – Hitch Control Unit Functions
HCU – Hitch Control Unit Reference List
HCU – Hitch Control Unit Schematic and Circuit Diagram
HCU – Hitch Control Unit System Power and Ground Circuit Test
HCU – Hitch Control Unit Sensor Power and Ground Circuit Test
HCU – Rear Hitch Draft Sensor Circuit Test
HCU – Rear Hitch Left External Switch Circuit Test
HCU – Rear Hitch Position Sensor Circuit Test
HCU – Rear Hitch Raise Solenoid Circuit Test
HCU – Rear Hitch Lower Solenoid Circuit Test
Group SE14B: SE14B — SCU – SCV Selective Control Unit Functions
SCU – SCV Selective Control Unit Reference List
SCU – SCV Selective Control Unit Schematic and Circuit Diagram
SCU – SCV Selective Control Unit System Power and Ground Circuit Test
SCU – SCV Selective Control Unit Sensor Power and Ground Circuit Test
SCU – SCV I Extend Solenoid Circuit Test
SCU – SCV I Retract Solenoid Circuit Test
SCU – SCV II Extend Solenoid Circuit Test
SCU – SCV II Retract Solenoid Circuit Test
SCU – SCV III Extend Solenoid Circuit Test
SCU – SCV III Retract Solenoid Circuit Test
SCU – SCV IV Extend Solenoid Circuit Test
SCU – SCV IV Retract Solenoid Circuit Test
SCU – SCV V Extend Solenoid Circuit Test (Scraper Only 10000-)
SCU – SCV V Retract Solenoid Circuit Test (Scraper Only 10000-)
SCU – SCV VI Extend Solenoid Circuit Test (Scraper Only 10000-)
SCU – SCV VI Retract Solenoid Circuit Test (Scraper Only 10000-)
SCU – Loop Back Circuit Test
SCU – Option Configuration Connector Test
SCU -TouchSet™ Depth Control Connector Test
SCU – Scraper AutoLoad™ Interconnect Harness Test
Group SE14D: SE14D — BRC – Brake System Control Unit Functions
BRC – Brake System Control Unit Reference List
BRC – Brake System Control Unit Schematic and Circuit Diagram
BRC – Brake Control Unit System Power and Ground Circuit Test
BRC – Brake Control Unit Sensor Supply Power and Ground Circuit Test
BRC – Front Brake Cooling Valve Solenoid Circuit Test
BRC – Rear Brake Cooling Valve Solenoid Circuit Test
BRC – Secondary Brake Pressure Sensor Circuit Test
BRC – Secondary Brake Control Valve Circuit Test
Group SE14CAN: SE14 CAN — SCC/HCC – Deluxe Hydraulic CAN Control Unit Functions
Deluxe Hydraulic Control Unit (SCC, HCC, BRC) Schematic and Circuit Diagram
Deluxe Hydraulic CAN Control Unit Test (SCC, HCC, BRC)
Deluxe Hydraulic CAN Control Unit Loop Back Circuit Test
HCC/SCC—CAN Communication Fault Test
A701 Selective Control Valve Unit I (SV1)
A702 Selective Control Valve Unit II (SV2)
A703 Selective Control Valve Unit III (SV3)
A704 Selective Control Valve Unit IV (SV4)
A705 Selective Control Valve Unit V (SV5)
A706 Selective Control Valve Unit VI (SV6)
A773 Deluxe Hydraulic CAN Control Unit (SCC, HCC) Theory
A773X1 Deluxe Hydraulic CAN Control Unit Connector
A773X2 Deluxe Hydraulic CAN Control Unit Connector
A773X3 Deluxe Hydraulic CAN Control Unit Connector
A800 Hitch Control Valve Unit
Group SE14ACAN: SE14A CAN — SCC – Selective CAN Control Unit Functions
SCC—SV I and II Power and Ground Circuit Test
SCC—SV III and IV Power and Ground Circuit Test
SCC—SV V and VI Power and Ground Circuit Test
SCC—Option Configuration Connector Circuit Test
SCC—TouchSet™ Depth Control Connector Circuit Test
Group SE14BCAN: SE14B CAN — HCC – Hitch CAN Control Unit Functions
HCC—Hitch Control Unit Sensor Power and Ground Circuit Test
HCC—Rear Hitch Position Sensor Circuit Test
HCC—Rear Hitch Draft Sensor Circuit Test
HCC—Rear Hitch External Switch Circuit Test
HCC—HV I Power and Ground Circuit Test
Group SE15: SE15 — SCO – Secondary Hydraulic Control Unit Functions
SCO – Secondary Hydraulic Control Unit Reference List
SCO – Secondary Hydraulic Control Unit Schematic and Circuit Diagram
SCO – Optional EH Control Unit System Power and Ground Circuit Test
SCO – SCV V Extend Solenoid Circuit Test
SCO – SCV V Retract Solenoid Circuit Test
SCO – SCV VI Extend Solenoid Circuit Test
SCO – SCV VI Retract Solenoid Circuit Test
SCO – Loop Back Circuit Test
A772—Optional EH Control Unit (SCO) (SE15)
A772X2—SCO Connector (SE15) (W802)
A772X3—SCO Connector (SE15) (W802)
X802—SCO to SCV VI Harness Interconnect (SE15) (W802, W878)
X810—Chassis Harness to SCV IV (SCV V Option) (SE14B, SE15) (W300, W301, W303, W873, W877)
Y840—SCV V Extend Solenoid (SE15) (W873, 879)
Y841—SCV V Retract Solenoid (SE15) (W873)
Y870—SCV VI Extend Solenoid (SE15) (W878)
Y871—SCV VI Retract Solenoid (SE15) (W878)
Group SE16A: SE16A — Engine Control Unit (ECU) Level 14 (9.0L) Functions
ECU – Engine Control Unit Level 14 (9.0L) (SE16A) Reference List
ECU – Engine Control Unit Level 14 (9.0L) (SE16A) Schematic and Circuit Diagram
ECU – Engine Control Unit Level 14 (9.0L) (SE16A) System Power and Ground Test
ECU – Engine Control Unit Level 14 (9.0L) (SE16A) Variable Fan Drive Speed Control Solenoids Circuit Test
ECU – Engine Control Unit Level 14 (9.0L) (SE16A) Variable Fan Drive Speed Sensor Test
A400—Engine Control Unit (ECU) (9L) (SE16A)
A401—Variable Speed Fan Drive (SE16A)
A400X1—ECU Connector (9L) (SE16A) (W300)
A400X2—ECU Connector (9L) (SE16A) (W300)
A400X3—ECU Connector (9L) (SE16A) (W300)
A431—Turbo Actuator (SE16A) (W300)
B400—Fuel Temperature Sensor (9L) (SE16A) (W300)
B401—Engine Coolant Temperature Sensor (9L) (SE16A) (W300)
B402—Water-In-Fuel Sensor (9L) (SE16A) (W300)
B404—Fuel Rail Pressure Sensor (9L) (SE16A) (W300)
B405—Cam Position Sensor (9L) (SE16A) (W300)
B406—Crank Position Sensor (9L) (SE16A) (W300)
B407—Engine Oil Pressure Sensor (9L) (SE16A) (W300)
B410—Manifold Air Pressure Sensor (9L) (SE16A) (W300)
B430—Turbo Speed Sensor (9L) (SE16A) (W300)
B431—Fan Speed Sensor (9L) (SE16A) (W300)
B432—Exhaust Temperature Sensor (9L) (SE16A) (W300)
B433—Fresh Air Temperature Sensor (9L) (SE16A) (W300)
B434—Manifold Air Temperature Sensor (9L) (SE16A) (W300)
B435—EGR Valve Position Sensor (9L) (SE16A) (W300)
B436—Compressor Inlet Temperature Sensor (9L) (SE16A) (W300)
B438—Fuel Pressure Sensor (9L) (SE16A) (W300)
M430—EGR Actuator (9L) (SE16A) (W300)
M431—Fuel Transfer Pump (9L) (SE16A) (W300)
Y400—Cylinder #1 Electronic Injector (9L) (SE16A) (W400)
Y401—Cylinder #2 Electronic Injector (9L) (SE16A) (W400)
Y402—Cylinder #3 Electronic Injector (9L) (SE16A) (W400)
Y403—Cylinder #4 Electronic Injector (9L) (SE16A) (W400)
Y404—Cylinder #5 Electronic Injector (9L) (SE16A) (W400)
Y405—Cylinder #6 Electronic Injector (9L) (SE16A) (W400)
Y430—Fan Output Drive 1 (9L) (SE16A) (W300)
Y431—Fan Output Drive 2 (9L) (SE16A) (W300)
Group SE16B: SE16B — Engine Control Unit (ECU) Level 15 (13.5L) Functions
ECU – Engine Control Unit Level 15 (13.5L) (SE16B) Reference List
ECU – Engine Control Unit Level 15 (13.5L) (SE16B) Schematic and Circuit Diagram
ECU – Engine Control Unit Level 15 (13.5L) (SE16B) System Power and Ground Test
ECU – Engine Control Unit Level 15 (13.5L) (SE16B) Variable Fan Drive Speed Control Solenoids Circuit Test
ECU – Engine Control Unit Level 15 (13.5L) (SE16B) Variable Fan Drive Speed Sensor Test
A301—Variable Speed Fan Drive (SE16B)
A330—Engine Control Unit (ECU) (13.5L) (SE16B)
A330X1—ECU Connector (13.5L) (SE16B) (W301, W303)
A330X2—ECU Connector (13.5L) (SE16B) (W301, W303)
A330X3—ECU Connector (13.5L) (SE16B) (W301, W303)
A331—Turbo Actuator (SE16B) (W301, W303)
B330—Engine Coolant Temperature Sensor (13.5L) (SE16B) (W301, W303)
B331—Fuel Temperature Sensor (13.5L) (SE16B) (W402)
B332—Water-In-Fuel Sensor (13.5L) (SE16B) (W301, W303)
B333—Manifold Air Pressure Sensor (13.5L) (SE16B) (W301, W303)
B334—Fuel Pressure Sensor (13.5L) (SE16B) (W402)
B335—Crank Position Sensor (13.5L) (SE16B) (W301, W303)
B336—Cam Position Sensor (13.5L) (SE16B) (W301, W303)
B337—Compressor Inlet Temperature Sensor (13.5L) (SE16B) (W301, W303)
B338—Fuel Pump Pressure Sensor (13.5L) (SE16B) (W402)
B339—Engine Oil Pressure Sensor (13.5L) (SE16B) (W301, W303)
B340—Exhaust Temperature Sensor (13.5L) (SE16B) (W301, W303)
B341—Fresh Air Temperature Sensor (13.5L) (SE16B) (W301, W303)
B342—Manifold Air Temperature Sensor (13.5L) (SE16B) (W301, W303)
B343—Fan Speed Sensor (13.5L) (SE16B) (W301, W303)
B344—Turbo Speed Sensor (13.5L) (SE16) (W301, W303)
M330—EGR Actuator (Front) (13.5L) (SE16B) (W301, W303)
M331—EGR Actuator (Rear) (13.5L) (SE16B) (W301, W303)
M332—Fuel Transfer Pump (13.5L) (SE16B) (W402)
Y330—Cylinder #1 Electronic Injector (13.5L) (SE16B)
Y331—Cylinder #2 Electronic Injector (13.5L) (SE16B)
Y332—Cylinder #3 Electronic Injector (13.5L) (SE16B)
Y333—Cylinder #4 Electronic Injector (13.5L) (SE16B)
Y334—Cylinder #5 Electronic Injector (13.5L) (SE16B)
Y335—Cylinder #6 Electronic Injector (13.5L) (SE16B)
Y340—Fan Output Drive 1 (13.5L) (SE16B) (W301, W303)
Y341—Fan Output Drive 2 (13.5L) (SE16B) (W301, W303)
Group SE17: SE17 — JDL – JDLink™Control Unit Functions
JDL – JDLink™ Control Unit Reference List
JDL – JDLink™ Control Unit Schematic and Circuit Diagram
A904—JDLINK™ Control Unit (SE17) (W902)
C910—GPS Antenna (SE17)
C910X1—JDLink™ GPS Antenna Connector (SE17)
C911—Cellular Antenna (SE17)
C911X1—JDLink™ Cellular Antenna Connector (SE17)
F69—(10A) JDLink™ Switched Power (SE17) (W901)
F70—(10A) JDLink™ Unswitched Power (SE17) (W901)
Group SE18: SE18 — GreenStar™ Display, Receiver, & Processor
Greenstar™ Display Reference List
Greenstar™ Display Schematic and Circuit Diagram
A906—Reconfigurable Display (SE18)
A907—GreenStar™ Display (SE18)
A907X1—GreenStar™ Display Connector (SE18) (W903)
A908—GPS Receiver (SE18)
A908X1—StarFire™ Receiver Connector (SE18) (W920)
A909—Mobile Processor (SE18)
A909X1—Mobile Processor Connector (SE18) (W903)
A910—User Interface Module (SE18)
A910X1—User Interface Connector (SE18) (W500, W501, W504)
A913—CAN Implement Passive Terminator (SE18) (W300, W301, W303)
A914—CAN Implement Active Terminator (SE18) (W920)
B921—Radar Sensor (SE18) (W300, W301, W303)
X921—Implement Connector (SE18) (W300, W301, W303)
X923—ISO Connector (W922)
Group SE20: SE20 — SSU – Steering System Control Unit Functions
SSU – Steering System Control Unit Reference List
SSU – Steering System Control Unit (SSU) Schematic and Diagram (SE20)
SSU – Steering System Control Unit Loop Back Circuit Test
SSU – Steering System Control Unit System Power and Ground Circuit Test
SSU – Electro-Hydraulic Steering Valve Manual / Circuit Test
SSU – Steering Wheel Position Sensor 1 Circuit Test
SSU – Steering Wheel Position Sensor 1 Current Test
SSU – Steering Wheel Position Sensor 2 Circuit Test
SSU – Steering Wheel Position Sensor 2 Current Test
SSU – Steering Angle Sensor Circuit Test
A980— Steering System Control Unit (SSU) (AutoTrac™) (SE20)
A980X1—SSU Connector (SE20) (W700)
A980X2—SSU Connector (SE20) (W700)
A980X3—SSU Connector (SE20) (W700)
A982—Steering Input Device (SE20)
B957—Steering Wheel Position Sensor 1 (AutoTrac™) (SE20) (W992)
B958—Steering Wheel Position Sensor 2 (AutoTrac™) (SE20) (W992)
B959—Steering Angle Sensor (AutoTrac™) (SE20) (W700)
Y952—Electro-Hydraulic Steering Valve (AutoTrac™) (SE20) (W300, W301, W303)
Group SE21: SE21 — Front Driveshaft Health Control Unit Schematic
FDH – Front Driveshaft Health Control Unit Reference List
FDH – Front Driveshaft Health Control Unit Schematic and Circuit Diagram
FDH – Front Driveshaft Health Control Unit Power and Ground Circuit Test
FDH—Proximity Sensor Circuit Test
A002X1 Front Driveshaft Health Control Unit Connector
B001 Proximity Sensor
F40 Front Driveshaft Health Control Unit Power Fuse
Section 245: CONTROL UNITS
Group 05: General References
Access Control Unit Addresses
Control Unit Locations and Identification
Recall, Record and Clear Codes
Programming Control Units
VIN Security Fault Diagnosis
Group ACU: ACU
Armrest Control Unit (ACU) Calibration
Armrest Control Unit (ACU) ”Beep” Mode Test
Armrest Control Unit (ACU) Address List
Armrest Control Unit Test
Group ASU: ASU
ActiveSeat™ Control Unit (ASU) Calibration
ActiveSeat™ Control Unit ”Beep” Mode Test
ASU Address List
ActiveSeat™ Unit (ASU) Special Adjustment Addresses
Group ATC: ATC
Automatic Temperature Control Unit (ATC) Calibration
Automatic Temperature Control Unit (ATC) ”Beep” Mode Test
Automatic Temperature Control Unit (ATC) Address List
Automatic Temperature Control Unit Test
Group BRC: BRC
Brake Control Unit (BRC) Calibration
Brake Control Unit (BRC) ”Beep” Mode Test
Brake Control Unit (BRC) Address List
Group CAB: CAB
CAB Control Unit Address List
CAB Control Unit ”Beep” Mode Test
CAB Control Unit Calibration
Cab Control Unit (CAB and ASU) Test
Group CCU: CCU
Chassis Control Unit (CCU) Address List
Chassis Control Unit (CCU) “Beep” Mode Test
Chassis Control Unit (CCU) Calibration
Chassis Control Unit (CCU) Special Adjustment Addresses
Group CLC: CLC
Cab Load Center Control Unit (CLC) Address List
Cab Load Center (CLC) Control Unit “Beep” Mode Test
Cab Load Center Control Unit (CLC) Calibration
Implement Gateway Control Unit (CLC and TEC) Test
Group ECU: ECU
Programming Engine Control Unit (ECU)
Engine Control Unit (ECU) ”Beep” Mode Test
Engine Control Unit (ECU) Address List
Engine Control Unit (ECU) Level 14 (9.0L) (SE16A) Test
Engine Control Unit (ECU) Level 15 (13.5L) (SE16B) Test
Group FDH: FDH
Front Driveshaft Health Control Unit (FDH) Address List
000—Device ID Address
FDH 001—Control Unit Stored Codes
FDH 002—FDH System Beep Mode
FDH 003—FDH Battery Voltage
FDH 004—FDH Switched ELX Voltage
FDH 010—FDH Sensor Supply Voltage
FDH 011—Proximity Sensor Voltage
FDH 012—Proximity Sensor Distance (mm)
FDH 013—Proximity Sensor Runout (mm)
FDH 014—Proximity Sensor Overall Max Runout (mm)
FDH 020—Runout Exceeded DTC Timer (ms)
FDH 021—Proximity Sensor Failed in Range DTC Timer (ms)
FDH 022—Proximity Sensor Saturated DTC Timer (ms)
FDH 023—Wheel Speed Sensor Activity Status (hrs)
200—251—Control Unit General Data
Front Driveshaft Health Control Unit Test
Group HCC: HCC
Rear Hitch Control Unit (HCC) Configuration and Calibration
000—Device ID Address
HCC 001—Control Unit Stored Codes
HCC 002—System Beep Mode
HCC 003—Option Jumper Status
HCC 004—Rear Hitch Position Sensor Voltage
HCC 005—Rear Hitch Draft Sensor Voltage
HCC 007—Rear Hitch External Switch
HCC 013—Rear Hitch Sensor Supply Voltage
HCC 014—Control Unit Switched Supply Voltage
HCC 015—Control Unit Unswitched Supply Voltage
HCC 016—Hitch CAN Valve Supply Voltage
HCC 019—Hydraulic Oil Temperature
HCC 020—Rear Hitch Calibration
HCC 021—Rear Hitch Configuration Options
HCC 023—Rear Hitch Raise Valve Maximum Current
HCC 024—Rear Hitch Raise Rate Adjustment
HCC 026—Rear Hitch Draft Sensor Voltage Adjustment
HCC 027—Rear Hitch Lower Draft Sensor Gain Adjustment
HCC 028—Rear Hitch Position Minimum Voltage
HCC 029—Rear Hitch Position Maximum Voltage
HCC 030—Rear Hitch Operator Command
HCC 031—Rear Hitch Valve Command
HCC 032—Rear Hitch Valve CAN Feedback
HCC 041—Rear Hitch Cylinder Speed
HCC 042—Rear Hitch Command Setting
HCC 043—Rear Hitch Raise Limit Control Setting
HCC 044—Rear Hitch Drop Rate Setting
HCC 045—Rear Hitch Load/Depth Mix Setting
HCC 046—Rear Hitch Slip Setting
HCU 047—Rear Hitch Slip Threshold Setting
HCC 147—Valve CAN Bus High Monitor
HCC 148—Valve CAN Bus Low Monitor
HCC 149—Valve Bus TLAs
HCC 219 — Control Unit Configuration Data Part Number
HCC 220 — Control Unit Configuration Data Version Number
HCC 222 — HCC Version Number
HCC 225 — Software Part Number
HCC 226 — Software Version Number
HCC 227 — HCC Boot Block Program Part Number
HCC 228 — HCC Boot Block Program Version Number
HCC 231 — Operating System Software Part Number
HCC 232 — Operating System Software Version Number
HCC 233 — HCC Software Part Number
HCC 234 — HCC Software Version Number
HCC 235 — HCC Part Number
HCC 236 — HCC Version Number
HCC 237 — Software Assembly Part Number
HCC 238 — Software Assembly Version Number
HCC 245 — CAN Bus OFF Retries Number
HCC 246 — CAN Bus OFF Intervals
HCC 251 — Current Vehicle John Deere PIN
Group HCU: HCU
Hitch Control Unit (HCU) Calibration
Hitch Control Unit (HCU) ”Beep” Mode Test
Hitch Control Unit (HCU) Address List
Group HV1: HV1
Rear Hitch Valve (HV1) Configuration and Calibration
000—Device ID Address
HV1 001—HV1 Control Unit Stored Codes
HV1 011—HV1 Supply Voltage
HV1 025—HV1 Enable/Disable Pressure Message
HV1 026—HV I Enable/Disable Pressure Measurement
HV1 030—Spool Position Temperature Compensation for Extend
HV1 031—Spool Position Temperature Compensation for Retract
HV1 033—Raise/Lower Ramp Time ON
HV1 034—Raise/Lower Ramp Time OFF
HV1 180—186—Factory Use Only
HV1 190—191—Factory Use Only
HV I 226 — Software Version Number
HV I 228 — HV I Boot Block Program Version Number
HV I 233 — HV I Software Part Number
HV I 234 — HV I Software Version Number
HV I 235 — HV I Part Number
HV I 236 — HV I Version Number
HV I 245 — CAN Bus OFF Retries Number
HV I 246 — CAN Bus OFF Intervals
Group ICU: ICU
Instrument Control Unit (ICU) Calibration
Instrument Control Unit (ICU) “Beep” Mode Test
ICU Address List
CommandCenter™ Control Unit (ICU) Test
Group PTP: PTP
Power Train Power Shift Control Unit (PTP) Calibration
Power Train Power Shift Control Unit (PTP) Address List

Group SCC: SCC
Selective Control Valve Control Unit (SCC) Configuration and Calibration
000—Device ID Address
001—Control Unit Stored Codes
002—System Beep Mode
003—Option Jumper Status
004—Remote Sensor 1 Voltage
005—Remote Sensor 2 Voltage
006—Remote Sensor 3 Voltage
007—Remote Sensor 4 Voltage
011—Option Sensor Connector Supply Voltage
013—Control Unit Switched Supply Voltage
014—Control Unit Unswitched Supply Voltage
015—Supply Voltage for SV III and IV
018—Supply voltage for SV I and II
020—SV I—VI Configuration
021—Laser Scraper Setup Mode
023—SCV Presence
031—SV I Operator Command Status
032—SV II Operator Command Status
033—SV III Operator Command Status
034—SV IV Operator Command Status
035—SV V Operator Command Status
036—SV VI Operator Command Status
041—SV I Valve Command
042—SV II Valve Command
043—SV III Valve Command
044—SV IV Valve Command
045—SV V Valve Command
046—SV VI Valve Command
051—SV I Valve Feedback
052—SV II Valve Feedback
053—SV III Valve Feedback
054—SV IV Valve Feedback
055—SV V Valve Feedback
056—SV VI Valve Feedback
060—SV I and SV II Supply Voltage
061—SV III and SV IV Supply Voltage
062—SV V and SV VI Supply Voltage
100—SV Lock Status
101—Adjust SV I Flowrate Setting
102—Adjust SV II Flowrate Setting
103—Adjust SV III Flowrate Setting
104—Adjust SV IV Flowrate Setting
105—Adjust SV V Flowrate Setting
106—Adjust SV VI Flowrate Setting
111—Adjust SV I Detent Time Setting
112—Adjust SV II Detent Time Setting
113—Adjust SV III Detent Time Setting
114—Adjust SV IV Detent Time Setting
115—Adjust SV V Detent Time Setting
116—Adjust SV VI Detent Time Setting
132—Single Lever Control Button Switches
133—Single Lever Control Transport Switch
134—Single Lever Control Operator Hand Presence Switch
147—Monitor Valve Bus CAN High
148—Monitor Valve Bus CAN Low
151—Autoload Draft Loop Gain Adjustment
152—Scraper Configuration
153—AutoLoad Scraper Blade to Axle
154—AutoLoad Scraper Blade to Blade
155—Scraper Position Entry Setting
156—Autoload Minimum Aggressiveness at Maximum Slip Setting
180—199—Factory Use Only
219 — Control Unit Configuration Data Part Number
220 — Control Unit Configuration Data Version Number
222 — Version Number
225 — Software Part Number
226 — Software Version Number
227 — Boot Block Program Part Number
228 — Boot Block Program Version Number
231 — Operating System Software Part Number
232 — Operating System Software Version Number
233 — Software Part Number
234 — Software Version Number
235 — Part Number
236 — Version Number
237 — Software Assembly Part Number
238 — Software Assembly Version Number
245 — CAN Bus OFF Retries Number
246 — CAN Bus OFF Intervals
251 — Current Vehicle John Deere PIN


Group SCO: SCO
Secondary Hydraulic Control Unit (SCO) Calibration
Secondary Hydraulic Control Unit (SCO) ”Beep” Mode Test
Secondary Hydraulic Control Unit (SCO) Address List
Secondary Hydraulic Control Unit (SCO) Test
Group SCU: SCU
Selective Control Unit (SCU) Calibration
Selective Control Unit (SCU) ”Beep” Mode Test
Selective Control Unit (SCU) Address List
Deluxe Hydraulic Control Unit Test (SCU, SFA, BRC, HCU)
Group SSU: SSU
Steering System Control Unit (SSU) Address List
Steering System Control Unit (SSU) ”Beep” Mode Test
Steering System Control Unit (SSU) Calibration
Steering System Control Unit (SSU) Special Adjustment Addresses
Steering System Control Unit (SSU) Test
Group SUP: SUP
Set-Up Panel Control Unit (SUP) Calibration
SUP Address List
SCV Set-Up Panel Control Unit Test
Group SV: SV1—SV7
SV Configuration and Calibration
000—Device ID Address
SV 001—SV Control Unit Stored Codes
SV 011—SV Supply Voltage
SV 025—SV Enable/Disable Pressure Message
SV 026—SV Enable/Disable Pressure Measurements
SV 030—Degree Celsius per Spool Position Change for Extend
SV 031—Degree Celsius per Spool Position Change for Retract
SV 033—Raise and Lower Ramp Time ON
SV 034—Raise and Lower Ramp Time OFF
SV 180—186—Factory Use Only
SV 190—191—Factory Use Only
SV 226 — Software Version Number
SV 228 — SCC Boot Block Program Version Number
SV 233 — SCC Software Part Number
SV 234 — SCC Software Version Number
SV 235 — SCC Part Number
SV 236 — SCC Version Number
SV 245 — CAN Bus OFF Retries Number
SV 246 — CAN Bus OFF Intervals
Group TEC: TEC
Tractor Equipment Control Unit (TEC) Address List
Tractor Equipment Control Unit (TEC) ”Beep” Mode Test
Tractor Equipment Control Unit (TEC) Calibration
Group VLC: VLC
Vehicle Load Center (VLC) Control Unit Address List
Vehicle Load Center (VLC) Control Unit ”Beep” Mode Test
Vehicle Load Center (VLC) Control Unit Calibration
Vehicle Control Unit (CCU and VLC) Test
Section 250: POWERSHIFT TRANSMISSION

Section 256: DRIVE SYSTEMS
Group 05: Axles and Differential Lock
Axles and Diff Lock – Reference List
Axles and Diff Lock – Preliminary Checks
Axles – Operational Pressure Checks (Early Design)
Axles – Operational Pressure Checks (Late Design)
Axles – Operational Checks
Diff Lock – Operational Checks
I
Group 56: Drive Systems Install Test Equipment
roup 60: Steering and Brakes Install Test Equipment
70: Hydraulics Install Test Equipment

Group 90: Operator Station Install Test Equipment
Install Test Equipment 90-1
Install Test Equipment 90-2
Install Test Equipment 90-3

John Deere 9230 9330 9430 9530 9630 Diagnosis Manual